P0116
DTC P0116
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0116
- Engine Coolant Temperature (ECT) Sensor Performance
Diagnostic Fault Information
Typical Scan Tool Data
Circuit Description
The engine coolant temperature (ECT) sensor is a variable resistor that measures the temperature of the engine coolant. The engine control module (ECM) supplies 5 volts to the ECT signal circuit and supplies a ground to the low reference circuit. The ECM monitors the performance of the ECT and the intake air temperature (IAT) signals. The ECM monitors the warm up and cool down behavior of the sensors, after a vehicle driven at operating temperature is shut down. If the ECM detects that the ECT is not with in a predetermined range of IAT after a long soak, or the ECT and IAT are not within a range of each other, as compared to a previous cold start, this DTC sets.
The following table illustrates the difference between temperature, resistance, and voltage:
Conditions for Running the DTC
* Before the ECM can report DTC P0116 failed, DTC P0117, P0118, and P2610 must run and pass.
* The actual engine coolant temperature during the previous ignition cycle was greater than 85°C (185°F).
OR
* The engine was operating for greater than 10 minutes in the previous ignition cycle.
* The accumulated air mass of the previous ignition cycle was greater than 6,007 grams.
* The ignition was OFF for greater than 317 minutes after the previous engine shut down.
* The calculated engine coolant temperature is less than 50°C (120°F).
* The DTC runs once an ignition cycle when the above conditions are met for greater than 35 seconds.
Conditions for Setting the DTC
The ECM determines the difference between the actual and the calculated ECT at ignition ON is greater 14°C (25°F) when the enable conditions are met.
Action Taken When the DTC Sets
DTC P0116 is a Type A DTC.
Conditions for Clearing the MIL/DTC
DTC P0116 is a Type A DTC.
Diagnostic Aids
* Test the ECT sensor at various temperature levels in order to evaluate the possibility of a skewed sensor. A skewed sensor can result in a DTC or a driveability condition. Refer to Temperature Versus Resistance - Engine Coolant Temperature Sensor (Temperature Versus Resistance - Engine Coolant Temperature Sensor) and Temperature Versus Resistance - Intake Air Temperature Sensor (Temperature Versus Resistance - Intake Air Temperature Sensor).
* If the vehicle has sat overnight, the IAT sensor and the ECT sensor values should display within 3°C (5°F).
* After starting a cold engine, the ECT sensor temperature should rise steadily, then stabilize after the thermostat opens.
* High resistance in the circuits of either the ECT sensor could set a DTC.
* A short to ground or voltage through a conductive material or fluid could set this DTC. Inspect the ECT sensor for evidence of engine coolant leaking into the connector body.
Reference Information
Schematic Reference
Engine Controls Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition OFF, open the hood to disable the Auto-Stop function.
2. Ignition ON, verify the scan tool hood position parameter displays Open.
• If the hood position does not display Open, refer to DTC P254F (P254F).
3. Observe the DTC information with a scan tool. Verify that DTC P0117, P0118, or P0119 is not set.
• If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions).
4. Inspect the engine coolant level. Verify that the cooling system is operating correctly.
• If there is a condition with engine cooling system, refer to Symptoms - Engine Cooling (Symptom Related Diagnostic Procedures).
5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, open the hood to disable the Auto-Stop function.
2. Ignition ON, verify the scan tool hood position parameter displays Open.
• If the hood position does not display Open, refer to DTC P254F (P254F).
3. Ignition OFF, disconnect the ECT sensor.
4. Ignition ON, verify that the scan tool ECT sensor parameter is at -40°C (-40°F).
• If greater than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the ECM.
5. Ignition OFF, remove the fuse that supplies B+ to circuit terminal X2-56 of the ECM.
Caution: Do NOT use a test lamp to test the continuity of the circuit. Damage to the control module may occur due to excessive current draw.
Note: The control module or the sensor may be damaged if the circuit is shorted to battery positive voltage.
6. Test for less than 5 ohm between the low reference circuit terminal 2 and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance, or for a short to voltage. If the circuit tests normal, replace the ECM.
7. Install the fuse that supplies B+ to circuit terminal X2-56 of the ECM.
Note: If the fuse in the jumper wire opens, the signal circuit is shorted to a voltage and the sensor may be damaged.
8. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal 1 and ground. Verify the ECT sensor parameter is greater than 142°C (288°F).
• If less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
9. If all circuits test normal, test or replace the ECT sensor.
Component Testing
1. Ignition OFF, disconnect the harness connector at the engine coolant temperature (ECT) sensor.
Note: A thermometer can be used to test the sensor off the vehicle.
2. Test the ECT sensor by varying the sensor temperature while monitoring the sensor resistance. Compare the readings with the Temperature Versus Resistance - Engine Coolant Temperature Sensor (Temperature Versus Resistance - Engine Coolant Temperature Sensor) table and verify that the resistance is within 5 percent of the specification.
• If not within the specified range, replace the ECT sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Engine Coolant Temperature Sensor Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for engine control module replacement, setup, and programming