Torque Specifications

Air Cleaner Box-to-Battery Tray Bolts 10 N.m (89 lb in)
Air Cleaner Box-to-Frame Rail Bolt 10 N.m (89 lb in)
Back-Up Light Switch-to-Shift Control Housing Assembly 38 N.m (28 lb ft)
Battery Hold Down-to-Battery Tray Bolt & Nut 9 N.m (80 lb in)
Battery Hold Down-to-Frame Rail Bolt 9 N.m (80 lb in)
Battery Terminal-to-Battery Bolt 17 N.m (150 lb in)
IMPORTANT: Attach positive then, negative terminal.
Battery Tray-to-Side of Frame Rail Bolts 10 N.m (89 lb in)
Battery Tray-to-Top of Frame Rail Bolts 10 N.m (89 lb in)
Brake Master Cylinder-to-Brake Booster Nuts 27 N.m (20 lb ft)
Case-to-Clutch Housing Bolts 28 N.m (21 lb ft)
IMPORTANT: Refer to service procedure for Torque Sequence.
Case-to-Clutch Housing Studs 28 N.m (21 lb ft)
IMPORTANT: Refer to service procedure for Torque Sequence.
Catalytic Converter-to-Intermediate Exhaust Pipe Bolt & Nut 25 N.m (18 lb ft)
Clutch Fork Ball Stud 24 N.m (18 lb ft)
Cradle-to-Body Bolts 210 N.m (155 lb ft)
Clutch Hydraulic Damper Bracket-to-Case Studs 25 N.m (18 lb ft)
Clutch Pedal Pivot Shaft Attachment Nut 17 N.m (150 lb in)
Clutch Pressure Plate Cover Assembly-to-Flywheel 25 N.m (18 lb ft)
Clutch Start Switch Attachments Nuts 10 N.m (89 lb in)
Dust Cover-to-Clutch Housing Bolts 11 N.m (97 lb in)
End Cover-to-Case Bolts 12 N.m (106 lb in)
IMPORTANT: Refer to Service Procedure for torque sequence.
Engine Strut Bracket-to-Cradle Nuts 59 N.m (37 lb ft)
Floor Shifter-to-Body Nuts 25 N.m (18 lb ft)
Flywheel-to-Crankshaft Bolts 80 N.m (59 lb ft)
Front Brake Hose Bracket-to-Inner Fender Bolt 5 N.m (44 lb in)
Front Exhaust Pipe Hanger Strap Clamp 60 N.m (44 lb ft)
Front Exhaust Pipe Hanger-to-Powertrain Stiffening Bracket Bolts 30 N.m (22 lb ft)
Front Lower Control Arm Ball Stud-to Steering Knuckle Nut 75 N.m (55 lb ft)
IMPORTANT: Align slot in nut to cotter pin hole.
Input Shaft Clamp Nut 150 N.m (111 lb ft)
IMPORTANT: Always use a new nut.
Intermediate Shaft Support Bracket-to-Engine Bolts 54 N.m (40 lb ft)
Intermediate Shaft Support Bracket-to-Engine Stud 54 N.m (40 lb ft)
Output Shaft Clamp Nut 150 N.m (111 lb ft)
IMPORTANT: Always use a new nut.
Park Neutral Position and Back- Up Light Switch- to-Case Bolts 14 N.m (124 lb in)
Powertrain Stiffening Bracket-to-Engine Bolts 54 N.m (40 lb ft)
Powertrain Stiffening Bracket-to-Transaxle Bolts 54 N.m (40 lb ft)
Reverse Shift Lever Assembly-to-Clutch Housing 14 N.m (124 lb in)
IMPORTANT: Apply Loctite(R) 242 Threadlocker (or equivalent).
Sensor-Vehicle Speed Sensor-to-Clutch Housing 26 N.m (19 lb ft)
Shift Cable Pass-Through Grommet Nuts 6 N.m (53 lb in)
Shift Control Housing Assembly-to-Case Bolts 28 N.m (21 lb ft)
Steering Gear-to-Cradle Bolt & Nut 50 N.m (37 lb ft)
Steering Linkage Outer Tie Rod-to-Steering Knuckle Nut 45 N.m (33 lb ft)
IMPORTANT: Align slot in nut to cotter pin hole.
Transaxle Drain Plug 30 N.m (22 lb ft)
Transaxle-to-Engine Bolts 140 N.m (103 lb ft)
Transaxle-to-Engine Studs 100 N.m (74 lb ft)
Transaxle Mount-to-Case Bolts 32 N.m (24 lb ft)
Transaxle Mount-to-Cradle Nut 50 N.m (37 lb ft)
Transaxle Strut, Transaxle Bracket-to-Case Bolts 54 N.m (40 lb ft)
Transaxle Strut-to-Midrail Bracket Bolt 50 N.m (37 lb ft)
Transaxle Strut-to-Transaxle Bracket Bolt 70 N.m (52 lb ft)
Wheel Lug Nuts 140 N.m (103 lb in)