Operation CHARM: Car repair manuals for everyone.

Removal

IMPORTANT: Record preset radio stations and clock time. Disconnect negative battery cable.

1. Disable the SIR System.

NOTE: Use of any lubricants on instrument panel or console components will deteriorate the plastic.




2. Remove screws and carefully pull right and left end cap assemblies outward at clip locations.




3. Remove screws and remove arm rest, if equipped.




4. Lift parking brake lever.
5. Remove screw.
6. Remove parking brake cover by lifting straight off lever.




7. Move shifter to neutral. Remove ashtray from cup holder by lifting straight out.
8. Remove cup holder from console by pulling upwards starting at rear edge.




9. Remove ashtray bulb socket by lifting tab while sliding socket forward. Then pull socket straight out.
10. Remove wiring harness from cup holder.




11. Remove window/mirror switch, if equipped, by sliding switch forward then lifting at rear edge. Disconnect electrical connectors.




12. If vehicle does not have an arm rest, remove rear screw cover by lifting at cut out.
13. Remove rear console screws.




14. Remove left and right lower trim panel extensions by pulling outward at dual lock locations. Then rotate panels outward to disengage hinges from console.




15. Remove front console screws.
16. Move console rearward.
17. Disconnect cigarette lighter electrical connector.
18. Remove bulb socket from cigarette lighter by rotating clockwise and pulling straight out.




19. On automatic transmission equipped vehicles, tape shifter button in to clear shifter opening.
20. Lift console at rear. Slide console rearward and lift straight up to remove.




21. Depress center pins inward to release radio/HVAC controller cover push pin fasteners.

IMPORTANT: Do not push center pins through fasteners.

22. Remove fasteners and pull radio/HVAC controller cover rearward.
23. Disconnect traction control/fog lamp/rear defog electrical connector if equipped.




24. Remove radio screws.
25. Push spring clips in through D-holes on both sides of radio brace.
26. Pull radio out slightly to access rear of radio.




27. Disconnect electrical connector and antenna.
28. Remove radio.




29. Disconnect blower switch, A/C-Recirc and lighting electrical connectors.




30. Remove temperature and mode cables from HVAC control by squeezing lock tabs together while pulling cable housing straight up.
31. Remove cables from pins by pulling straight up. (Service cables shown in illustration.)




32. Remove screws and HVAC controller.




33. Remove closeout seal by releasing from tabs.




34. Remove screw and ground wire from H-bracket.
35. Remove wiring harness from H-bracket.




36. Remove screw and disconnect rear electrical connector from instrument panel junction block.




37. Remove instrument panel junction block screw.
38. Insert a small flat blade screwdriver from passenger side, to release lock tabs on instrument panel junction block and slide off of mounting pads.
39. Feed instrument panel junction block through H-bracket towards front of car.




40. Remove bolts from H-bracket.




41. Remove screws from data link connector (DLC) and steering column filler panel.




42. Remove hood release cable from lever by releasing cable housing, then rotating cable downward to cutout.
43. Remove steering column filler panel.




44. Disconnect ignition switch electrical connector at right steering column bolt.
45. Remove steering column bolts and lower column on front seat.




46. Remove fasteners and pull instrument cluster trim bezel rearward at clip locations.
47. Disconnect electrical connector from instrument panel dimmer switch.




48. Remove connector position assurance (CPA) devices and disconnect electrical connectors from instrument cluster by squeezing tabs on each side of connector.




49. Remove front and rear instrument cluster screws.
50. Remove instrument cluster.




51. Remove dimmer switch wiring harness from instrument panel reinforcement.
52. Feed connector through reinforcement towards front of car.




53. Remove passenger side air bag harness from cross car beam and energy absorber.




54. Remove glove box door stops by rotating 90 degrees and let door hang down.
55. Remove screws from glove box compartment and striker.
56. Remove glove box assembly by pulling rearward at clip locations.




57. Disconnect antenna cable at lower right side of instrument panel reinforcement.




58. Remove screws and passenger side air bag.

IMPORTANT: Use illustration to determine fastener location and direction of removal.




59. Remove instrument panel fasteners.

NOTE: Put instrument panel pad/reinforcement on a clean surface so that the surface does not become damaged.




60. Remove nut, screws and instrument panel pad/reinforcement assembly.




61. Rotate center outlets down.
62. Push at top of outlets through back side.
63. Remove outlets.




64. Use a small flat blade screw driver to disengage lock tabs on both sides of center outlet housing while pulling housing rearward.
65. Remove housing.