Revised Service Procedures: Overview
BULLETIN NO.: 99-T-24ISSUE DATE: July, 1999
GROUP/SEQ. NO.: Engine-05
CORPORATION NO.: 99-06-01-013
SUBJECT:
Service Manual Update for All the 2000 L-Series L61 Engine Service Manuals
MODELS AFFECTED:
2000 Saturn L-Series Sedans and Wagons equipped with L61 (4 cyl.) engines
PURPOSE:
The purpose of this bulletin is to update all the 2000 L-Series L61 Engine Service Manuals at your location. Please go through this bulletin carefully and make the necessary updates in the service manual as indicated.
Obtain all the 2000 L-Series L61 Engine Service Manuals at your location and update according to the information contained in this bulletin.
^ On page 389, toward bottom of page under step 5, write in the following new procedure step.
6. Install fuel tank grounding strap nut located near fuel filter.
Torque: 4.5 N.m (40 in-lbs).
^ On page 393, cross out existing Important statement above step 3 and write in the following new important statement.
IMPORTANT:
The fuel pump module to tank seal must always be replaced and lubricated with clean engine oil whenever module is removed from fuel tank.
^ On page 395, write in the following new Important statement above step 12.
IMPORTANT:
The fuel pump module to tank seal must always be replaced and lubricated with clean engine oil whenever module is removed from fuel tank.
^ On page 404, write in the following new Important statement above step 3.
IMPORTANT:
The fuel pump module to tank seal must always be replaced and lubricated with clean engine oil whenever module is removed from fuel tank.
^ On page 405, cross out step 5 and illustration in middle of page.
^ On page 408, write in the following new Important statement above step 3.
IMPORTANT:
The fuel pump module to tank seal must always be replaced and lubricated with clean engine oil whenever module is removed from fuel tank.
^ On page 410, cross out step 4 and illustration in middle of page.
^ On page 413, write in the following new Important statement at the top of the page above step 4.
IMPORTANT:
The fuel pump module to tank seal must always be replaced and lubricated with clean engine oil whenever module is removed from fuel tank.
^ On page 415, under FUEL PRESSURE REGULATOR installation procedure, cross out existing Important statement and write in the following new Important statement.
IMPORTANT:
Both 0-rings must be oiled with clean engine oil and installed into fuel rail prior to installing fuel pressure regulator.
^ On page 415, under FUEL PRESSURE REGULATOR installation procedure, cross out existing step 1 and write in the following new step 1.
1. Install small oiled 0-ring into fuel rail.
^ On page 437, under FUEL CUT-OFF MODE near bottom of page, cross out the SOHC and DOHC information and write in the following:
L61 Auto/Manual Trans. 4000 rpm in Park/Neutral
6400 rpm in Gear
^ On page 532, under step 2, write in the following procedure steps.
2.1 Install water pump sprocket and retaining bolts.
Torque: 10 N.m (89 in-lbs).
2.2 Install water pump sprocket access plate.
^ On page 630, before step 1 of Engine Flywheel Installation procedure, write in the following Notice statement.
NOTICE:
Ensure that the correct bolts are used when installing manual transaxle flywheel or automatic transaxle flexplate. If the incorrect bolts are used, powertrain damage may result.
^ Make photo copies of page 4 of this bulletin. Turn to page 378 and write in the following after step 3 and insert photo copy between pages 378 and 379. (Refer to inserted illustration.)
^ Make photo copies of pages 5 - 7 of this bulletin. Turn to page 725 and 726 and cross out the entire Engine Oil and Oil Filter Replacement procedure. Insert photo copies of pages 4-6 made from this bulletin before page 725.
Photo copies of this page are to be made and inserted between pages 378 and 379 of all the 2000 L-Series L61 Engine Service Manuals at your location. Also, write in the following after step 3 on page 378:
(Refer to inserted illustration.)
Photo copies of pages 5-7 are to be made and inserted in all the 2000 L-Series L61 Engine Service Manuals at your location. After making photo copies, turn to page 725 and cross out the entire Engine Oil and Oil Filter Replacement procedure. Insert photo copies before page 725.