P0966
DTC P0965, P0966 or P0967
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
* Review Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P0965
- Clutch Pressure Control (PC) Solenoid 2 System Performance
DTC P0966
- Clutch Pressure Control (PC) Solenoid 2 Control Circuit Low Voltage
DTC P0967
- Clutch Pressure Control (PC) Solenoid 2 Control Circuit High Voltage
Diagnostic Fault Information
Circuit/System Description
The clutch pressure control (PC) solenoid 2 is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The transmission control module (TCM) supplies 12 volts to the clutch PC solenoid 2 on the high side driver 2 circuit. The TCM control the PC solenoid 2 through the clutch PC solenoid 2 control circuit. The normally high clutch PC solenoid 2 flows fluid to the 3-5-R clutch when commanded OFF and exhausts fluid when commanded ON. The clutch PC 2 regulates the transmission fluid pressure to the 3-5-R clutch.
Conditions for Running the DTC
* The engine run time is greater than 5 seconds.
* The ignition voltage is between 8.6 volts and 19.0 volts.
* The clutch PC solenoid 2 is commanded ON.
P0965
DTC P0965 has not failed this ignition cycle.
P0966
DTC P0966 has not failed this ignition cycle.
P0967
DTC P0967 has not failed this ignition cycle.
Conditions for Setting the DTC
P0965
The TCM detects an internal electrical performance malfunction of the clutch PC solenoid control circuit and the actual 3-5-R clutch pressure does not equal the commanded 3-5-R clutch pressure for 4.4 seconds.
P0966
The TCM detects an internal low voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds.
P0967
The TCM detects an internal high voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds.
Action Taken When the DTC Sets
* DTC P0965 is a Type C DTC.
* DTCs P0966 and P0967 are Type A DTCs.
* The TCM defaults the transmission to a limited shift pattern utilizing 2 forward gears and reverse based on the fault detected.
* The TCM commands maximum line pressure.
* The TCM freezes transmission adaptive functions.
Conditions for Clearing the DTC
* DTC P0965 is a Type C DTC.
* DTCs P0966 and P0967 are Type A DTCs.
Diagnostic Aids
When attempting to set solenoid electrical DTCs, it may be helpful to ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
Circuit/System Verification
Perform the following procedure to place the control solenoid (w/body and TCM) valve assembly under the optimal conditions to test solenoid electrical DTCs.
1. Ensure the transmission fluid temperature is between 50-80°C (122-176°F).
2. Operate the vehicle in second gear long enough to ensure at least a 3°C (5°F) rise in TCM substrate temperature and then operate the vehicle in third gear for 5 seconds.
Component Testing
The scan tool data parameter Clutch PC 2 Sol. CKT Status normally displays OK.
If the parameter displays Open/Short to Volts, Short to GND or if the DTC resets, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection and if no concerns are found replace the control solenoid (w/body and TCM) valve assembly. Control Solenoid Valve and Transmission Control Module Assembly Inspection
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests
1. Replace the control solenoid (w/body and TCM) valve assembly. Refer to programming and relearning for replacement, setup, and programming.
2. Perform the Service Fast Learn Adapts. Programming and Relearning