Operation CHARM: Car repair manuals for everyone.

P0971



DTC P0969, P0970 or P0971

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
* Review Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0969
- Clutch Pressure Control (PC) Solenoid 3 System Performance

DTC P0970
- Clutch Pressure Control (PC) Solenoid 3 Control Circuit Low Voltage

DTC P0971
- Clutch Pressure Control (PC) Solenoid 3 Control Circuit High Voltage

Diagnostic Fault Information





Typical Scan Tool Data





Circuit/System Description

The clutch pressure control (PC) solenoid 3 is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The TCM supplies 12 volts to the clutch PC solenoid 3 on the high side driver 2 circuit. The TCM control the clutch PC solenoid 3 through the clutch PC solenoid 3 control circuit. The normally high clutch PC solenoid 3 flows fluid to the low and reverse clutch and 4-5-6 clutch assemblies when commanded ON and exhausts fluid when commanded OFF. The clutch PC solenoid 3 regulates the transmission fluid pressure to the low and reverse clutch and 4-5-6 clutch assemblies.

Conditions for Running the DTC

* The engine run time is greater than 5 seconds.
* The ignition voltage is between 8.6 volts and 19.0 volts.
* The clutch PC solenoid 3 is commanded ON.

P0969

DTC P0969 has not failed this ignition cycle.

P0970

DTC P0970 has not failed this ignition cycle.

P0971

DTC P0971 has not failed this ignition cycle.

Conditions for Setting the DTC

P0969

The TCM detects an internal electrical performance malfunction of the clutch PC solenoid control circuit and the actual low and reverse/4-5-6 clutch pressure does not equal the commanded low and reverse/4-5-6 clutch pressure for 4.4 seconds.

P0970

The TCM detects an internal low voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds.

P0971

The TCM detects an internal high voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds.

Action Taken When the DTC Sets

* DTC P0969 is a Type C DTC.
* DTCs P0970 and P0971 are Type A DTCs.
* The TCM defaults the transmission to a limited shift pattern utilizing 2 forward gears and reverse based on the default detected.
* The TCM commands maximum line pressure.
* The TCM freezes transmission adaptive functions.

Conditions for Clearing the DTC

* DTC P0969 is a Type C DTC.
* DTCs P0970 and P0971 are Type A DTCs.

Diagnostic Aids

When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.

Circuit Verification

Perform the following procedure to place the control solenoid (w/body and TCM) valve assembly under the optimal conditions to test solenoid electrical DTCs.

* Ensure the transmission fluid temperature is between 50-80°C (122-176°F).
* Operate the vehicle in second gear long enough to ensure at least a 3°C (5°F) rise in TCM substrate temperature and then operate the vehicle in fourth gear for 5 seconds.

Component Testing

The scan tool data parameter Clutch PC 3 Sol. CKT Status normally displays OK.

If the parameter displays Open/Short to Volts or Short to GND or if the DTC resets, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection and if no concerns are found, replace the control solenoid (w/body and TCM) valve assembly. Control Solenoid Valve and Transmission Control Module Assembly Inspection

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests

1. Replace the control solenoid (w/body and TCM) valve assembly. Refer to programming and relearning for replacement, setup, and programming.
2. Perform the Service Fast Learn Adapts. Programming and Relearning