Battery Cassette Replacement - AURA
Battery Cassette Replacement - AURAImportant:
Dust may be an irritant to skin and eyes. Avoid skin and eye contact. If battery dust is present, remove carefully to avoid inhalation. Wear safety glasses and butyl rubber, natural rubber, neoprene, nitrile or Tyvek protective gloves when handling any corroded hybrid batteries and when cleaning the inside of the hybrid battery case. Discard the gloves after each use and dispose of any corrosion material that was removed from the case.
1. Remove the ignition key from the ignition switch. Secure the ignition key in order to ensure that the key CANNOT be reinstalled without your knowledge.
2. Disconnect the 12-volt negative battery cable.
3. Fold down both rear seat backs.
4. Carefully lift up on the load floor rear compartment cover (1) at the retaining clip (2) locations.
5. Tilt the load floor rear compartment cover (2) towards the rear of the vehicle slightly, disengaging the tabs (1) and remove the load floor rear compartment cover.
6. Remove the generator battery disconnect control module cover bolt.
7. Slide the generator battery disconnect control module cover to the right and remove the cover.
8. WAIT at least 5 minutes in order to allow the generator control module capacitors to discharge.
Important:
Never assume the battery pack is disabled when the generator battery disconnect control module cover is opened.
9. The generator battery will have to be checked for voltage potential using a voltmeter. First, verify that the voltmeter works.
1. Set the voltmeter to DC voltage.
2. Measure the vehicle's 12-volt battery voltage (at 12-volt positive jumper location and negative battery cable).
3. The meter should read greater than +12 volts DC.
10. Now, check the generator battery for voltage potential in order to ensure that the generator battery has been disabled.
1. Measure from the positive (3) stud to the negative stud (2). The voltage should be less than 3 volts.
2. Measure from the positive (3) stud to vehicle chassis ground (1). The voltage should be less than 3 volts.
3. Measure from the negative (2) stud to vehicle chassis ground (1). The voltage should be less than 3 volts.
4. After verifying that there is no voltage present, the vehicle is now safe to work on.
11. Remove the 36-volt negative battery cable ground nut (1).
12. Remove the 36-volt positive battery cable retainer bolt (1).
13. Remove and discard the 36-volt positive battery cable lead nut (3).
14. Remove the 36-volt positive battery cable lead nut (1).
15. Remove the 36-volt positive battery cable leads (2).
16. Secure the cables out of the way, ensuring that the cables CANNOT be reinstalled without your knowledge.
17. Disconnect the body wiring harness electrical connector (1) from the generator battery disconnect control module pigtail.
18. Remove the generator battery carrier nuts (2).
19. With the aid of an assistant, lift the generator battery carrier up off of the studs, and rotate and position the carrier towards the rear of the vehicle.
20. With the aid of an assistant, remove the generator battery carrier out through the truck opening. Place the carrier on a workbench.
21. Remove the two upper generator battery fan bolts (2).
22. Remove the 12 generator battery cover bolts (1).
23. Remove the generator battery wiring harness from the clip (3) on the generator battery cover.
24. Remove the generator battery cover.
Important:
Removing the interconnect cables will disable the 36 volts within the generator battery control module.
25. Remove the generator battery terminal covers (1).
26. Remove the generator battery cable nuts (2).
27. Remove and reposition the generator battery cable leads (3, 4, 5) from the batteries.
28. Disconnect the generator battery temperature sensor wiring harness electrical connectors (1) from the battery temperature sensors.
29. Cut the tie straps securing the battery cables to the generator battery temperature sensor wiring harness.
30. Disconnect the generator battery temperature sensor wiring harness electrical connectors (2, 5) from the generator control module.
31. Remove the generator battery temperature sensor wiring harness.
32. Remove the remaining generator battery cable from the battery.
33. Remove all the mounting bolts (1) from the 3 generator batteries.
Important:
Each hybrid battery must be placed in two (double) polyethylene 6 mil bags that were provided with the new batteries. If the bags were not included with the batteries, contact your Saturn Parts Service Analysis (PSA) or the Saturn Saab Service Parts Assistance Centre (SPAC) for Canadian retailers. This double bagging procedure must be performed as soon as the hybrid batteries are removed from the vehicle. After bagging the individual battery cassettes, place the batteries in the original shipping container.
34. Remove all 3 generator batteries.
35. Remove the 3 temperature sensors from the batteries.
36. Remove the four generator battery control module assembly bolts.
37. Remove the generator battery control module assembly from the carrier.
38. Remove the two remaining lower vent fan bolts and fan from carrier.
Important:
Only perform Steps 39-41 if the corrosion or battery acid is present.
39. Clean any corrosion or battery acid that is present on the inside of the hybrid battery case by using a sponge that is lightly dampened with soapy water. It is not necessary to use a neutralizer, such as baking soda.
40. Dry the inside of the hybrid battery case using several shop towels.
41. Apply black paint to any areas inside of the hybrid battery case where bare metal is present.
42. Install the vent fan to the carrier and secure with two lower bolts.
43. Install the generator battery control module assembly to the carrier.
44. Install the generator battery control module assembly bolts.
45. Install the 3 temperature sensors to the new batteries. Polarity does NOT matter.
46. Install the new generator batteries.
47. Install the generator battery bolts.
Tighten
Tighten the bolts to 10 N.m (89 lb in).
48. Position and install the generator battery temperature sensor wiring harness.
49. Connect the generator battery temperature sensor wiring harness electrical connectors to the battery temperature sensors.
50. Connect the generator battery temperature sensor wiring harness electrical connectors to the generator control module.
Important:
The cable leads must be installed correctly to prevent low voltage DTCs. It is recommended that the disassembly and reassembly be performed at the same time to ensure reinstalling the cables in the correct location. In the event that the battery cable routing is in question, it is important to remember that the battery cable stud and plate covers up (not visible) the polarity indicator in the plastic case. The polarity that is visible is for the terminal NEXT to the stud. This visible polarity indicator is NOT for the battery stud. This was covered in the BAS hybrid training.
51. Position and install the generator battery cable leads to the battery terminals.
52. Install the generator battery cable nuts to the batteries.
Tighten
Tighten the nuts to 8 N.m (71 lb in).
53. Install the generator battery terminal covers.
54. Install NEW tie straps in order to secure the battery cables to the generator battery temperature sensor wiring harness.
55. Install the generator battery cover.
56. Install the 12 generator battery cover bolts.
Tighten
Tighten the bolts to 8 N.m (71 lb in).
57. Install the two generator battery fan bolts.
Tighten
Tighten the bolts to 8 N.m (71 lb in).
58. With the aid of an assistant, install the generator battery carrier in through the truck opening and rotate and position the carrier towards the front of the vehicle.
59. With the aid of an assistant, lift the generator battery carrier up onto the studs.
60. Install the generator battery carrier nuts.
Tighten
Tighten the nuts to 25 N.m (18 lb ft).
61. Connect the body wiring harness electrical connector to the generator battery disconnect control module pigtail.
62. Install the 36-volt positive battery cable leads.
63. Install the 36-volt positive battery cable lead nut.
Tighten
Tighten the nuts to 9 N.m (18 lb in).
64. Install a NEW 36-volt positive battery cable lead nut. Start the nut finger-tight, and then torque to the specification given.
Tighten
Tighten the nuts to 15 N.m (11 lb ft).
65. Position the 36-volt positive battery cable retainer to the fan cover.
66. Install the 36-volt positive battery cable retainer bolt.
Tighten
Tighten the bolt to 8 N.m (71 lb in).
67. Install the 36-volt negative battery cable ground nut.
Tighten
Tighten the nut to 9 N.m (80 lb in).
68. Install the generator battery cover bolt.
Tighten
Tighten the bolt to 10 N.m (89 lb in).
69. Tilt the load floor rear compartment cover towards the rear of the vehicle slightly in order to insert the tabs into the battery tray rear support.
70. Set the load floor rear compartment cover down, ensuring that the retaining clips align to the proper locations, carefully push down, securing the cover.
71. Return both rear seat backs to their proper positions.
72. Connect the 12-volt negative battery cable.
73. Reprogram the ECM with the latest calibrations if a P1A5A DTC was stored with the P1A59 DTC.
74. After programming, clear any DTC codes that may be present.
Important:
Hybrid parts are no longer on restriction through TAC. All hybrid parts can now be ordered through your parts department.
Important:
For U.S. Retailers: Hybrid battery cassette replacement was recently covered in the October Emerging Issues Seminar (10207.10D). An archived copy of this training seminar should be stored on your Genesis IDL Box. It is also available on the GM Training Website (www.gmtraining.com). This training seminar highlights BDU and hybrid battery cassette replacement. Once this video is loaded to the GM Training Website and you log in, you will be able to take the following path to locate and view the October Emerging Issues Seminar (10207.10D):
1. Click the Service Know-How/TECHAssist hyperlink on the left side of the screen.
2. Click the Emerging Issues hyperlink in the center of the screen.
3. Click the Searchable Streaming Video hyperlink in the center of the screen.
4. Enter the course number 10207.10D in the search box on the left side of the screen and click Search.
Important:
For Canadian Retailers, refer to December 2007 TAC TALK. CALIFORNIA, MASSACHUSETTS, MAINE, & VERMONT VEHICLES ONLY: Install a Recall Identification Label. Also, for California vehicles complete a "Proof of Correction" certificate upon recall completion.
75. Refer to the section titled "Returning the Battery".