Frame Replacement (2.4L)

Frame Replacement (2.4L)

Special Tools
J 39580 Engine Support Stand
Removal Procedure

1.Install the engine support fixture. Refer to Engine Support Fixture .

2.Support the radiator and condenser from above using the condenser tabs on each side.

3.Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle .

4.Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .

5.Remove the front fender liner. Refer to Front Fender Liner Replacement Service and Repair .

6.LE5 only, remove the front catalytic converter. Refer to Catalytic Converter Replacement .

7.Remove the engine splash shields. Refer to Engine Splash Shield Replacement Engine Splash Shield Replacement , Engine Splash Shield Replacement - Left Side and Engine Splash Shield Replacement - Right Side .





8.Remove the lower ball joints from the steering knuckles. Refer to Lower Control Arm Replacement .

1.Remove the tie rod ends from the steering knuckles. Refer to Steering Linkage Outer Tie Rod Replacement .





2.Remove both stabilizer links from the stabilizer bar. Refer to Stabilizer Shaft Link Replacement .

3.Separate the steering gear from the intermediate shaft. Refer to Intermediate Steering Shaft Replacement .





1.Remove the front transmission mount bolt from the frame. Refer to Transmission Front Mount Replacement .

2.Remove the rear transmission mount bracket fasteners from the frame. Refer to Transmission Rear Mount Replacement .





1.Lower the vehicle until the frame contacts the J 39580 .





1.Remove the reinforcement bolts (1).





1.Remove the front frame bolts (1).

2.Remove the rear frame bolts (4).

3.Remove the frame reinforcements (3).

4.Raise the vehicle off of the frame.

5.Remove the following components if replacing the frame:

-The steering gear - Refer to Steering Gear Replacement .

-The lower control arms - Refer to Lower Control Arm Replacement .

-The stabilizer shaft - Refer to Stabilizer Shaft Replacement .

-The radiator support brackets

Installation Procedure

1.Install the following components on the suspension crossmember if removed:

-The radiator support brackets

-The stabilizer shaft - Refer to Stabilizer Shaft Replacement .

-

-The lower control arms - Refer to Lower Control Arm Replacement .

-The steering gear - Refer to Steering Gear Replacement .





2.Lower the vehicle on to the frame.

3.Install the frame reinforcements (3).

4.Install the front frame bolts. Hand tighten ONLY.

5.Install the reinforcement bolts. Hand tighten ONLY.

Notice:Refer to Fastener Notice .

6.Install the rear frame bolts (4).

TightenTighten the bolts to 100 N �m (74 lb ft) plus 90 degrees rotation.

7.Tighten the front frame bolts (1).

TightenTighten the bolts to 100 N �m (74 lb ft) plus 90 degrees rotation.





1.Install the cradle support bolts (1).

TightenTighten the bolts to 100 N �m (74 lb ft).

2.Raise the vehicle.

1.Install the rear transmission mount bracket fasteners. Refer to Transmission Rear Mount Replacement .





2.Install the front transmission mount bracket bolt. Refer to Transmission Front Mount Replacement .

3.Install the power steering gear mounting bolts. Refer to Steering Gear Replacement .

1.Connect the steering gear to the intermediate shaft. Refer to Intermediate Steering Shaft Replacement .





2.Install both stabilizer links to the stabilizer bar.

TightenTighten the stabilizer link nut to 65 N �m (48 lb ft).

3.Install the tie rod ends to the steering knuckles. Refer to Steering Linkage Outer Tie Rod Replacement .





1.Install the lower ball joints to the steering knuckles.

TightenTighten the ball stud to steering knuckle pinch nut to 50 N �m (37 lb ft). Reverse the nut � of a turn. Tighten to 50 N �m (37 lb ft) plus 60 degrees.

2.Install the front fender liner. Refer to Front Fender Liner Replacement Service and Repair .

3.Install the engine splash shields. Refer to Engine Splash Shield Replacement Engine Splash Shield Replacement , Engine Splash Shield Replacement - Left Side and Engine Splash Shield Replacement - Right Side .

4.Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .

5.LE5 only, install the front catalytic converter. Refer to Catalytic Converter Replacement .

6.Remove the engine support fixture.