Engine Oil Pressure Indicator Malfunction
Engine Oil Pressure Indicator Malfunction (LZ4 - Gas, 6 Cyl, 3.5L, SFI, V6, Offset Bore)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The engine oil pressure (EOP) sensor changes voltage based on the engine oil pressure. The EOP sensor is a 3-wire sensor comprising of the signal circuit, the low reference circuit and the 5-volt reference circuit. The engine control module (ECM) supplies 5-volts to the EOP sensor via the 5-volt reference circuit and provides ground via the EOP low reference circuit. The ECM monitors the signal circuit of the EOP sensor to determine the engine oil pressure sensor voltage is within the normal operating range of approximately 1-4 volts. When the engine oil pressure is high, the EOP sensor voltage is high and the ECM senses a high signal voltage. When the engine oil pressure is low, the EOP sensor voltage is low and the ECM senses a low signal voltage. The ECM sends the EOP information to the instrument panel cluster (IPC) via the serial data circuit.
Reference Information
Schematic Reference
Instrument Cluster Schematics (Instrument Cluster Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
* Instrument Cluster Description and Operation (Description and Operation)
* Indicator/Warning Message Description and Operation (Indicator/Warning Message Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine running, observe the scan tool Engine Oil Pressure Sensor parameter. The reading should be between 0.2-4.8 volts.
2. Verify the engine oil pressure, refer to Oil Pressure Diagnosis and Testing (Component Tests and General Diagnostics).
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the engine oil pressure (EOP) sensor.
2. Ignition OFF, test for less than 1 ohm between the low reference circuit terminal 1 and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 2 and ground.
• If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
• If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
4. Verify the scan tool Engine Oil Pressure Sensor parameter is less than 0.2 volt.
• If greater than the specified range, test the signal circuit terminal 3 for a short to voltage. If the circuit tests normal, replace the ECM.
5. Install a 3A fused jumper wire between the signal circuit terminal 3 and the 5-volt reference circuit terminal 2. Verify the scan tool Engine Oil Pressure Sensor parameter is greater than 4.8 volts.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
6. Ignition ON, command the indicators OFF with the scan tool.
• If the EOP indicator does not turn OFF, replace the IPC.
7. If all circuits test normal, test or replace the EOP sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Engine Oil Pressure Sensor and/or Switch Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for the PCM or IPC replacement, setup, and programming