Rear Seat
Rear Seat Assy:
REPLACEMENT
HINT: The installation procedures are the removal procedures in reverse order, However, only installation procedures requiring additional information are included.
CAUTION: Wear gloves because cutting surface of the seat cushion frame and seat adjuster may injure your hand.
1. REMOVE REAR SEAT CUSHION W/COVER PAD SUB-ASSEMBLY
a. Pull up the 2 front portions of the seat cushion, then remove it.
NOTE: In this case, hold the base of the clip up to prevent the cushion frame from being distored.
2. REMOVE REAR SEATBACK ASSEMBLY LH
a. Tilt down the seatback toward the front of the vehicle.
b. Turn up the seatback cover as shown in the illustration.
c. Remove the 2 bolts and seatback.
3. REMOVE REAR SEATBACK ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
4. REMOVE REAR SEATBACK LOCK STRIKER LH
a. Remove the 2 bolts and seatback lock striker.
5. REMOVE REAR SEATBACK LOCK STRIKER RH
a. Remove the nut, 2 bolts and seatback lock striker.
6. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
a. Remove the bolt and seatback hinge.
7. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
a. Remove the bolt and seatback hinge.
8. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY
a. Remove the 4 bolts and anchor bracket.
9. REMOVE REAR SEAT HEADREST ASSEMBLY
a. Remove the headrests.
10. REMOVE REAR SEATBACK LOCK RELEASE BUTTON
11. Only RH side:
REMOVE REAR SEAT SHOULDER BELT COVER
a. Using a screwdriver, remove the shoulder belt cover.
12. REMOVE TETHER ANCHOR COVER
a. Using a screwdriver, remove the 3 tether anchor covers.
13. REMOVE REAR SEAT HEADREST SUPPORT
a. Using a clip remover, remove the 17 clips.
NOTE: If clips are damaged during removal, replace them.
b. Remove the hog rings.
c. Disengage the claws and remove the seat headrest support.
HINT: When performing this step, position yourself between the seat-back frame and the seatback cover (with pad).
14. REMOVE REAR SEATBACK STOP BUTTON GROMMET
a. Disengage the claws and remove the seatback stop button grommet.
HINT: When performing this step, position yourself between the seat-back frame and the seatback cover (with pad).
15. REMOVE REAR SEATBACK COVER W/PAD LH
a. Remove the seatback cover (with pad) from the rear seatback frame.
16. REMOVE REAR SEATBACK COVER W/PAD RH
a. Remove the seatback cover (with pad) from the rear seatback frame.
17. REMOVE REAR SEATBACK LOCK ASSEMBLY LH
a. Remove the 2 bolts and seatback lock.
18. REMOVE REAR SEATBACK LOCK ASSEMBLY RH
a. Remove the 2 bolts and seatback lock.
19. REMOVE REAR SEAT BELT ASSEMBLY OUTER CENTER
a. Remove the nut and seat belt.
20. INSTALL REAR SEAT BELT ASSEMBLY OUTER CENTER
a. Install the seat belt with the nut.
Torque: 42 Nm (428 kgf.cm, 31 ft.lbf)
21. INSTALL REAR SEATBACK COVER W/PAD LH
a. Install the seatback cover (with pad) to the seatback frame.
NOTE: Do not damage or contaminate the seatback cover (with pad).
22. INSTALL REAR SEATBACK COVER W/PAD RH
HINT: Use the same procedures described for the LH side.
23. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY
a. Install the anchor bracket with the 4 bolts.
Torque: 42 Nm (428 kgf.cm, 31 ft.lbf)
24. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH
a. Install the seatback hinge with the bolt.
Torque: 42 Nm (428 kgf.cm, 31 ft.lbf)
25. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
a. Install the seatback hinge with the bolt.
Torque: 42 Nm (428 kgf.cm, 31 ft.lbf)
26. INSTALL REAR SEATBACK LOCK STRIKER LH
a. Install the seatback lock striker with the 2 bolts.
Torque: 21 Nm (214 kgf.cm, 15 ft.lbf)
27. INSTALL REAR SEATBACK LOCK STRIKER RH
a. Install the seatback lock striker with the 2 bolts and nut.
Torque: 21 Nm (214 kgf.cm, 15 ft.lbf)
28. INSTALL REAR SEATBACK ASSEMBLY LH
a. Install the seatback assembly with the 2 bolts.
Torque: 37 Nm (377 kgf.cm, 27 ft.lbf)
29. INSTALL REAR SEATBACK ASSEMBLY RH
a. Install the seatback assembly with the 2 bolts.
Torque: 37 Nm (377 kgf.cm, 27 ft.lbf)