Reassembly

SEAT: REAR SEAT ASSEMBLY: REASSEMBLY

REASSEMBLY
CAUTION: Wear protective gloves. Sharp areas on the seatback frame may injure your hands.

1. INSTALL REAR SEAT RECLINING CONTROL CABLE LH






(a) Install the 2 control cables as shown in the illustration.
2. INSTALL REAR SEATBACK COVER LH
NOTICE:





- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.

(a) Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
(b) Install the seatback cover (with pad) to the seatback frame.






(c) Attach the 4 claws to install the 2 headrest supports.






(d) Attach the 2 hooks and 2 claws, and install the seatback board to the seatback frame.






(e) Close the zipper.
(f) Using hog ring pliers, install the seatback cover (with pad) with new hog rings.
3. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH






(a) Install the 2 reclining control cables as shown in the illustration.






(b) Install the control lever to the seatback with the 2 screws.
(c) Attach the 2 claws to install the rear seatback lock striker cover.
4. INSTALL REAR SEAT RECLINING CONTROL CABLE RH
HINT: Use the same procedures described for the LH side.

5. INSTALL REAR SEAT SHOULDER BELT COVER RH






(a) Attach the 3 claws to install the belt cover.
6. INSTALL REAR SEAT OUTER BELT ASSEMBLY CENTER






(a) Install the belt with the nut as shown in the illustration.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
(b) Attach the hook.
(c) Align the holes of the 3 parts shown in the illustration, and then install the 3 nuts.





HINT: Before tightening the nuts, raise the seatback to the upright position and make sure the seatback stops in the first lock position of the frame.









(d) Attach the 2 claws to close the shoulder belt cover.
7. INSTALL REAR SEAT SIDE HINGE MALE COVER
(a) Attach the 2 claws to install the male cover.
8. INSTALL REAR SEAT SIDE HINGE MALE COVER LH






(a) Attach the claw to install the male cover.
9. INSTALL REAR SEAT SIDE HINGE MALE COVER RH






(a) Attach the 2 claws and install the male cover with the screws.
10. INSTALL REAR SEATBACK COVER RH





NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.

(a) Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
(b) Install the seatback cover (with pad) to the seatback frame.






(c) Attach the 4 claws to install the 2 headrest supports.






(d) Install the seatback board to the seatback frame.






(e) Close the zipper.
(f) Using hog ring pliers, install the seatback cover (with pad) with new hog rings.
11. INSTALL REAR SEAT SHOULDER BELT GUIDE CENTER






(a) Attach the 4 claws to install the belt guide.
12. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
HINT: Use the same procedures described for the LH side

13. INSTALL REAR NO. 2 SEAT RECLINING COVER LH






(a) Install the reclining cover with the clip.
14. INSTALL REAR NO. 1 SEAT RECLINING COVER LH
HINT: Use the same procedures described for the rear No. 2 seat reclining cover LH.

15. INSTALL REAR NO. 2 SEAT RECLINING COVER RH
HINT: Use the same procedures described for the LH side.





16. INSTALL REAR SEAT CUSHION COVER
(a) Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.

17. INSTALL REAR SEAT HEADREST ASSEMBLY LH
18. INSTALL REAR SEAT HEADREST ASSEMBLY RH
19. INSTALL REAR SEAT HEADREST ASSEMBLY CENTER