Programming and Relearning

METER: METER / GAUGE SYSTEM: CUSTOMIZE PARAMETERS

CUSTOMIZE PARAMETERS

1. SEAT BELT BUZZER ON/OFF SETTING
The buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.
NOTICE:
- These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).
- When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).
- Odometer returns to 0 after starting this procedure, although it is not displayed.
HINT:
- "b-oFF" indicates that the buzzer is OFF. "b-on" indicates that the buzzer is ON. The buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again.
- The legally required warning buzzer cannot be cancelled.
- The legally required warning buzzer is the buzzer that sounds when turn the ignition switch to the ON position and the driver seat belt is unfastened.
The buzzer sounds in order to warn the driver regardless of the vehicle speed.

(a) Driver side and passenger side seat belt buzzers
(1) Turn the ignition switch to the ON position.
(2) Press the ODO/TRIP switch until the odometer appears.
(3) Turn the ignition switch off.
(4) Turn the ignition switch to the ON position.
(5) Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
(6) Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.
(7) Check that the odometer displays either "b-ON" or "b-OFF"
(8) Press the ODO/TRIP switch to change the display to "b-OFF".
(9) Turn the ignition switch off.
(10) Turn the ignition switch to the ON position.
(11) Check that no buzzer sounds when the vehicle speed is 15 km/h (9 mph) or more and the driver seat belt is unfastened.
(b) Front passenger side seat belt buzzer
(1) Turn the ignition switch to the ON position.
(2) Press the ODO/TRIP switch until the odometer appears.
(3) Turn the ignition switch off.
(4) Turn the ignition switch to the ON position.
(5) Sit in the front passenger seat. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
(6) Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.
(7) Check that the odometer displays either "b-ON" or "b-OFF"
(8) Press the ODO/TRIP switch to change the display to "b-OFF".
(9) Turn the ignition switch off.
(10) Turn the ignition switch to the ON position.
(11) Check that no buzzer sounds when the vehicle speed is 15 km/h (9 mph) or more and the front passenger seat belt is unfastened.
HINT: "b-OFF" indicates that the buzzer is OFF. "b-ON" indicates that the buzzer is ON. The buzzer ON/OFF setting will be finished (the odometer will appear) if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again.
NOTICE:
- When either the battery cable or the combination meter connector is disconnected, these buzzers are set on.
- ODO/TRIP meter returns to 0 after starting this procedure, although it is not displayed.

2. RACING FUNCTION ON/OFF SETTING
The racing function is a function that the meter ECU moves needles to their maximum position and return to zero when turning the ignition switch to the ON position.
HINT:
- When either the battery cable or the combination meter connector is disconnected, this function is set on (enabled).
- "b-OFF" indicates that the function is OFF. "b-on" indicates that the function is ON. The racing function ON/OFF setting will be finished (the TRIP A meter will display TRIP A) if the ODO/TRIP switch is not operated for 5 seconds or more, or the ODO/TRIP switch is pressed for less than 1 second. In this case, perform procedure "B" to check that the function ON/OFF setting is complete. If it is not complete, start from procedure "A" again.

(a) Turn the ignition switch to the ON position (Procedure "A").
(b) Press the ODO/TRIP switch until the TRIP A meter appears.
(c) Turn the ignition switch off.
(d) Press the ODO/TRIP switch and hold it down.
(e) Turn the ignition switch to the ON position.
(f) Keep pressing the ODO/TRIP switch for 5 seconds or more.
(g) Check that the TRIP A meter displays either "b-on" or "b-oFF".
(h) Press the ODO/TRIP switch to change the display to "b-oFF".
(i) Turn the ignition switch off.
(j) Turn the ignition switch to the ON position.
(k) Check that each needle does not move to their maximum position (Procedure "B").