Smart Key System (for Start Function)

THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): DATA LIST / ACTIVE TEST

1. DATA LIST

HINT
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / (desired system) / Data List.

(e) According to the display on the Techstream, read the Data List.

Power Source Control













* *: for Automatic Transaxle





HINT
Get into the vehicle while carrying the electrical key transmitter. With the engine switch off and the shift lever in P, perform the following procedures and check the power source mode.

*1: Without depressing the brake pedal, press the engine switch and check that the power source mode turns on (ACC).

*2: Without depressing the brake pedal, press the engine switch and check that the power source mode turns on (IG).

*3: Depress the brake pedal (the stop light switch turns on).

*4: With the brake pedal depressed, press the engine switch and check that the engine starts.

*5: Press the engine switch and check that the power source mode turns off.

*6: Release the brake pedal.

*7: Open a door.





HINT
Get into the vehicle while carrying the electrical key transmitter. With the engine switch off, perform the following procedures and check the power source mode.

*1: Without depressing the clutch pedal, press the engine switch and check that the power source mode turns on (ACC).

*2: Without depressing the clutch pedal, press the engine switch and check that the power source mode turns on (IG).

*3: Depress the clutch pedal (the clutch start switch turns on).

*4: With the clutch pedal depressed, press the engine switch and check that the engine starts.

*5: Press the engine switch and check that the power source mode turns off.

*6: Release the clutch pedal.

*7: Open a door.

Smart Key





















HINT
Get into the vehicle while carrying the electrical key transmitter. With the engine switch off, the shift lever in P (for Automatic Transaxle) and all the doors closed, perform the following procedures and check the power source mode.

*1: Without depressing the brake pedal (for Automatic Transaxle) or clutch pedal (for Manual Transaxle), press the engine switch and check that the power source mode turns on (ACC).

*2: Without depressing the brake pedal (for Automatic Transaxle) or clutch pedal (for Manual Transaxle), press the engine switch and check that the power source mode turns on (IG).

*3: Press the engine switch and check that the power source mode turns off.

*4: Without depressing the brake pedal (for Automatic Transaxle) or clutch pedal (for Manual Transaxle), open the driver side door and check that the steering locks.

Starting Control









HINT
*: With the engine switch on (IG), the shift lever in P and the brake pedal (for Automatic Transaxle) or clutch pedal (for Manual Transaxle) depressed, press the engine switch and check that the engine starts.

Combination Meter





2. ACTIVE TEST

HINT
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / (desired system) / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Power Source Control





Smart Key





Starting Control