Reassembly
SEAT: FRONT SEAT ASSEMBLY: REASSEMBLY
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT
* Use the same procedure for the RH and LH sides.
* The procedure listed below is for the LH side.
1. INSTALL RECLINING ADJUSTER INSIDE COVER RH
(a) Move the cover in the direction of the arrow to install the cover.
(b) Attach the guide.
2. INSTALL RECLINING ADJUSTER INSIDE COVER LH (for Front Passenger Side)
HINT
Use the same procedure described for the RH side.
3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
(a) Install the seatback spring with the 4 bolts.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
4. INSTALL CAP
(a) Install the 2 caps to the seat cushion spring.
5. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)
(a) Attach the 6 clamps and claw to install the seat wire to the seat cushion spring.
(b) Connect the 4 connectors.
6. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) Installation
7. INSTALL SEAT POSITION SENSOR (for Driver Side) Installation
8. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY LH Installation
9. INSTALL SEAT LOCK CONTROL CABLE SUB-ASSEMBLY
(a) for Driver Side:
(1) Attach the 3 clamps to install the cable as shown in the illustration.
(2) Twist the 2 cable ends in the directions indicated by the arrows to connect the cable.
(3) Attach the 2 clamps of the cable end.
(b) for Front Passenger Side:
(1) Install the cable as shown in the illustration.
(2) Twist the 2 cable ends in the directions indicated by the arrows to connect the cable.
(3) Attach the 2 clamps of the cable end.
10. INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY (for Driver Side)
(a) Attach the clamp to install the cable as shown in the illustration.
(b) Twist the 2 cable ends in the directions indicated by the arrows to connect the cable.
(c) Attach the 2 clamps of the cable end.
11. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH (for Front Passenger Side)
(a) Attach the 2 clamps to install the cable as shown in the illustration.
(b) Twist the cable end in the direction indicated by the arrow to connect it.
(c) Attach the clamp of the cable end.
12. INSTALL RECLINING ADJUSTER EQUALIZING CABLE ASSEMBLY
(a) Install the cable as shown in the illustration.
(b) Twist the cable end in the direction indicated by the arrow to connect it.
(c) Attach the clamp of the cable end.
13. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
(a) Move the protector in the direction of the arrow to attach the 2 hooks and install the protector.
(b) Install the screw.
Text in Illustration
14. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
HINT
Use the same procedure described for the LH side.
15. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
(a) Attach the hook and clip to install the cushion shield.
(b) Install the screw.
16. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
HINT
Use the same procedure described for the LH side.
17. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) Installation
18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
(a) Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
(b) Connect the seatback cover bracket to the seatback pad.
19. INSTALL FRONT SEATBACK COVER WITH PAD
(a) Attach the 4 hooks to install the seatback cover with pad to the seatback spring.
(b) Attach the 4 claws to install the 2 headrest supports.
(c) Attach the 2 hooks and connect the seatback cover bracket to the seatback spring with the nut.
Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)
NOTICE:
After the seatback cover is installed, make sure the seatback cover bracket is not twisted.
(d) Using hog ring pliers, connect the strap of the seatback cover to the seatback spring with 3 new hog rings.
Text in Illustration
(e) for Cloth Seat:
Attach the hook and close the fastener to close the seatback cover.
(f) for Leather Seat:
Close the 2 fasteners to close the seatback cover.
(g) Using hog ring pliers, install 3 new hog rings.
Text in Illustration
20. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH
(a) Connect the cable to the control lever as shown in the illustration.
(b) Move the lever in the direction of the arrow to attach the guide.
(c) Install the control lever with the 2 screws.
21. INSTALL SEAT ADJUSTER COVER CAP
(a) Attach the guide and claw to install the cover cap.
22. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) Installation
23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
(a) Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
(b) w/ Seat Heater System:
Connect the seat cushion heater wire harness to the seat cushion cover.
24. INSTALL FRONT SEAT CUSHION COVER WITH PAD
(a) Install the seat cushion cover with pad to the seat cushion spring.
(b) Attach the hooks to the seat cushion spring.
(c) Connect the airbag wire harness and attach the fastening tape to close the cover of the rear part of the seat cushion cover.
(d) w/ Seat Heater System:
(1) Connect the seatback heater connector and attach the wire harness clamp of the rear part of the seat cushion cover.
(2) Attach the claw, connect the seat cushion heater connector and attach the wire harness clamps of the bottom of the seat cushion spring.
(e) Install the rubber band to the seat cushion spring.
25. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
(a) for Driver Side:
Installation
(b) for Front Passenger Side:
Installation
26. INSTALL FRONT SEAT INNER CUSHION SHIELD LH
(a) Attach the 4 claws to install the inner cushion shield.
27. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
(a) Attach the 4 claws to install the inner cushion shield.
28. INSTALL FRONT SEAT CUSHION SHIELD LH
(a) Attach the clamp to connect the cable to the cushion shield.
(b) Attach the 3 claws and clip to install the cushion shield.
(c) Attach the clamp to connect the cable to the cushion shield.
(d) Install the screw.
29. INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
(a) Attach the 4 claws and clip to install the cushion shield.
(b) Install the screw.
30. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)
(a) Install the handle with the screw.
31. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
(a) Attach the claw to install the handle.