Disassembly and Reassembly
DISASSEMBLY1. Disconnect four pipes from gearbox.
2. Secure gearbox removed from vehicle in vice using ST. ST 926200000 STAND
CAUTION: Secure the gearbox in a vice using the ST as shown. Do not attempt to secure it without this ST.
3. Remove tie-rod end and lock nut from gearbox.
4. Remove small clip from boot using pliers, and move boot to tie-rod end side.
5. Using standard screwdriver, remove band from boot.
6. Extend rack approximately 40 mm (1.57 inch) out. Unlock lock wire at lock washer on each side of tie-rod end using a standard screwdriver.
CAUTION: Be careful not to scratch rack surface as oil leaks may result.
7. Using ST, loosen lock nut. ST 926230000 SPANNER
8. Tighten adjusting screw until it no longer tightens.
9. Using a wrench [32 mm (1.26 inch) width across flats] or adjustable wrench, remove tie-rod.
CAUTION:
^ Check ball joint for free play, and tie-rod for bends. Replace if necessary.
^ Check dust seals used with tie-rod end ball joint for damage or deterioration. Replace if necessary.
10. Loosen adjusting screw and remove spring and sleeve.
CAUTION: Replace spring and/or sleeve if damaged.
INSPECTION
1. Clean all disassembled parts, and check for wear, damage, or any other faults, then repair or replace as necessary.
2. When disassembling, check inside of gearbox for water. If any water is found, carefully check boot for damage, input shaft dust seal, adjusting screw and boot clips for poor sealing. If faulty, replace with new parts.
1. Service Limit
Make a measurement as follows. If it exceeds the specified service limit, adjust or replace.
NOTE: When making a measurement, vise gearbox by using ST. Never vise gearbox by inserting aluminum plates, etc. between vise and gearbox. ST 926200000 STAND
Sliding resistance of rack shaft:
Service limit: 304.0 N (31.0 kg, 68.4 lbs.) or less
2. Rack Shaft Play In Radial Direction
Right-turn steering:
Service limit:
0. 15 mm (0.0059 inch) or less
On condition:
L: 5 mm (0.20 inch)
P: 98 N (10 kg, 22 lbs.)
Left-turn steering:
Service limit:
Direction <->: 0.3 mm (0.012 inch) or less
Direction <->: 0.15 mm (0.0059 inch) or less
3. Input Shaft Play
In radial direction:
Service limit: 0. 18 mm (0. 0071 inch) or less
On condition: P: 98 N (10 kg, 22 lbs.)
In axial direction:
Service limit: 0. 1 mm (0. 004 inch) or less
On condition: P: 20 - 49 N (2 - 5 kg, 4 - 11 lbs.)
4. Turning Resistance of Gearbox
Using ST, measure gearbox turning resistance. ST 926230000 SPANNER
Service limit:
Straight-ahead position within 30 mm (1. 18 inch) from rack center: Less than 11.18 N (1.14 kg, 2.51 lbs.)
Maximum allowable resistance: 12.7 N (1.3 kg, 2.9 lbs.)
ASSEMBLY
CAUTION: Use only SUBARU genuine grease for gearbox.
Grease: VALIANT GREASE M2 [Part No. 003608001, net 0.5 kg (1.1 lbs.)]
1. Clean all parts and tools before reassembling.
2. Apply grease to teeth of rack so that grease applied is about as high as teeth, and also apply a thin film of grease to sliding portion of rack shaft.
CAUTION:
^ When moving rack to stroke end without tie-rod attached, prevent shocks from being applied at the end.
^ Do not apply grease to threaded portion at end of rack shaft.
^ Move rack shaft to stroke end two (2) or three (3) times to squeeze grease which accumulates on both ends. Remove grease to prevent it from choking air passage hole.
3. Apply grease to sleeve insertion hole.
4. Apply grease to dust sea] insertion hole.
CAUTION: Apply clean grease with clean hands. If material having a sharp edge is used for applying grease, oil seal at the inside might be damaged.
5. Apply grease to sliding surface of sleeve and spring seat, then insert sleeve into pinion housing. Fit spring into sleeve screw, pack grease inside of s6rew, then install the screw.
6. Install lock washers and tighten left and right tie-rods into rack ends.
On condition: L: Approximately 40 mm (1.57 inch)
Tightening torque: 78 ± 10 Nm (8.0 ± 1.0 kg-m, 58 ± 7 ft. lbs.)
7. Bend lock washer using a chisel.
CAUTION: Be careful not to scratch rack when bending lock washer.
8. Rack and pinion backlash adjustment
1) Loosen adjusting screw.
2) Rotate input shaft so that rack is in the straight ahead direction.
3) Apply grease to sleeve.
4) Tighten adjusting screw by two threads.
5) Apply liquid packing to at least 1/3 of entire perimeter of adjusting screw thread.
Liquid packing: THREE BOND 1141
6) Tighten adjusting screw to 7.4 Nm (0.75 kg-m, 5.4 ft. lbs.) and back off 250.
7) Install lock nut. While holding adjusting screw with a wrench, tighten lock nut using ST ST 926230000 SPANNER
Tightening torque (Lock nut): 39 ± 10 Nm (4.0 ± 1.0 kg-m, 29 ± 7 ft. lbs.)
NOTE:
^ Hold adjusting screw with a wrench to prevent it from turning while tightening lock nut.
^ Make adjustment so that steering wheel can be rotated fully from lock to lock without binding.
9. Check for service limit as per article of "Service limit". Make replacement and adjustment if necessary.
10. Install boot to housing.
NOTE:
^ Before installing boot, be sure to apply grease to the groove of tie-rod.
^ Install fitting portions of boots to the following portions in both sides of assembled steering gearbox.
The groove on gearbox
The groove on the rod
^ Make sure that boot is installed without unusual inflation or deflation.
11. Using a screwdriver, tighten the screw until the ends "A" and "B" of the band come into contact with each other.
NOTE: Always tighten the band from the underside of the gear box.
12. Fix boot end with clip (small).
CAUTION: After installing, check boot end is positioned into groove on tie-rod.
13. If tie-rod end was removed, screw in lock nut and tie-rod end to screwed portion of tie-rod, and tighten lock nut temporarily in a position as shown in figure.
Installed tie-rod length: L: 15 mm (0.59 inch)
NOTE: Pay attention to difference between right and left tie-rod ends.
14. Inspect gearbox as follows: "A" Holding tie-rod end, repeat lock to lock two or three times as quickly as possible. "B" Holding tie-rod end, turn it slowly at a radius one or two times as large as possible. After all, make sure that boot is installed in the specified position without deflation.
15. Remove gearbox from ST. ST 926200000 STAND
16. Install four pipes on gearbox.
1) Connect pipes A and B to four pipe joints of gearbox. Connect upper pipe B first, and lower pipe A.
Tightening torque: 13 ± 3 Nm (1.3 ± 0.3 kg-m, 9.4 ± 2.2 ft. lbs.)
2) Connect pipes C and D to gearbox. Connect lower pipe C first, and upper pipe D second.
Tightening torque: 15 ± 5 Nm (1.5 ± 0.5 kg-m, 10.8 ± 3.6 ft. lbs.)