Operation CHARM: Car repair manuals for everyone.
Home >> Subaru >> 1999 >> Legacy L Wagon AWD F4-2.2L SOHC >> Repair and Diagnosis >> Powertrain Management >> Computers and Control Systems >> Testing and Inspection >> Reading and Clearing Diagnostic Trouble Codes >> Reading Diagnostic Trouble Codes >> With Manufacturer's Scan Tool >> Subaru Select Monitor

Subaru Select Monitor

HOW TO USE SUBARU SELECT MONITOR





1. Prepare Subaru Select Monitor kit.
2. Connect diagnosis cable to Subaru Select Monitor.





3. Insert cartridge into Subaru Select Monitor.

ST 24082AA090 CARTRIDGE

4. Connect Subaru Select Monitor to data link connector.








1. Open the cover data link connector located in the lower portion of the instrument panel (on the driver's side), to the lower cover.
2. Connect diagnosis cable to data link connector.

CAUTION: Do not connect scan tools except for Subaru Select Monitor and OBD-II general scan tool.





5. Turn ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
6. Using Subaru Select Monitor, call up diagnostic trouble code(s) and various data, then record them.

READ DIAGNOSTIC TROUBLE CODE (DTC) SHOWN ON DISPLAY FOR ENGINE. (NORMAL MODE)
1. On the [Main Menu] display screen, select the {1. All System Diagnosis} and press the [YES] key.
2. Make sure that a diagnostic trouble code (DTC) is shown on the {EGI/EMPI} display screen.

NOTE:
- For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
- For details concerning diagnostic trouble codes, refer to Trouble Code Descriptions.

READ DIAGNOSTIC TROUBLE CODE (DTC) SHOWN ON DISPLAY FOR ENGINE. (OBD MODE)
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {EGI/EMPI} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the [EGI/EMPI Diagnosis] display screen, select the {7. OBD System} and press the [YES] key.
5. On the [OBD Menu] display screen, select the {3. Diagnosis Code(s) Display} and press the [YES] key.
6. Make sure that a diagnostic trouble code (DTC) is shown on the display screen.

NOTE:
- For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
- For details concerning diagnostic trouble codes, refer to Trouble Code Descriptions.

READ CURRENT DATA SHOWN ON DISPLAY FOR ENGINE. (NORMAL MODE)
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {EGI/EMPI} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the [EGI/EMPI Diagnosis] display screen, select the {1. Current Data Display & Save} and press the [YES] key.
5. On the [Data Display Menu] display screen, select the {1. 12 Data Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.

Part 1 Of 2:




Part 2 Of 2:





- A list of the support data is shown in the table.

NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.

READ CURRENT DATA SHOWN ON DISPLAY FOR ENGINE. (OBD MODE)
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {EGI/EMPI} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the [EGI/EMPI Diagnosis] display screen, select the {7. OBD System} and press the [YES] key.
5. On the [OBD Menu] display screen, select the {1. Current Data Display & Save} and press the [YES] key.
6. On the [Data Display Menu] display screen, select the {1. 12 Data Display} and press the [YES] key.
7. Using the scroll key, move the display screen up or down until the desired data is shown.





- A list of the support data is shown in the table.

NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.

READ FREEZE FRAME DATA SHOWN ON DISPLAY FOR ENGINE. (OBD MODE)
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {EGI/EMPI} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the [EGI/EMPI Diagnosis] display screen, select the {7. OBD System} and press the [YES] key.
5. On the [OBD Menu] display screen, select the {2. Freeze Frame Data} and press the [YES] key.





- A list of the support data is shown in the table.

NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.

READ OXYGEN SENSOR MONITORING TEST RESULTS DATA SHOWN ON DISPLAY FOR ENGINE. (OBD MODE)
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {EGI/EMPI} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the [EGI/EMPI Diagnosis] display screen, select the {7. OBD System} and press the [YES] key.
5. On the [OBD Menu] display screen, select the {5. O2 Sensor Monitor} and press the [YES] key.
6. On the [O2 Sensor Select] display screen, select the {Bank 1-Sensor1} or {Bank 1-Sensor2} and press the [YES] key.

- Bank 1-Sensor1 indicates the front oxygen or A/F sensor, and Bank 1-Sensor2 indicates the rear oxygen sensor.





- A list of the support data is shown in the table.

NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.

LED OPERATION MODE FOR ENGINE
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {EGI/EMPI} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the [EGI/EMPI Diagnosis] display screen, select the {1. Current Data Display & Save} and press the [YES] key.
5. On the [Data Display Menu] display screen, select the {2. 6 Data & LED Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.





- A list of the support data is shown in the table.

NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.

READ CURRENT DATA SHOWN ON DISPLAY FOR AT.
1. On the [Main Menu] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [System Selection Menu] display screen, select the {AT/ECVT} and press the [YES] key.
3. Press the [YES] key after displayed the information of transmission type.
4. On the [E-4AT/ECVT Diagnosis] display screen, select the {1. Current Data Display & Save} and press the [YES] key.
5. On the [Data Display Menu] display screen, select the {1. 12 Data Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.





- A list of the support data is shown in the table.

NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.

pro multis · About Operation CHARM