Basic Diagnostics Procedure
6A1: CHECK SECURITY SYSTEM FUNCTION.1. Perform basic diagnostics procedure of keyless entry system.
2. Perform pre-inspection.
3. Open all windows.
4. Remove ignition key from ignition switch.
5. Set the room light switch in the middle position.
6. Close all doors, rear gate and trunk lid.
7. Press the LOCK/ARM button one time.
CHECK: Does the clearance light blink one time?
YES: Go to step 6A2.
NO: Go to step 6B1.
6A2: CHECK SECURITY SYSTEM FUNCTION.
Check if the security indicator light blinks.
CHECK: Does the security indicator light blink every 2 seconds?
YES: Go to step 6A3.
NO: Go to step 6C1.
6A3: CHECK SECURITY SYSTEM FUNCTION.
Press the UNLOCK/DISARM button one time.
CHECK: Does the clearance light blink two times?
YES: Go to step 6A4.
NO: Replace security control module.
6A4: CHECK SECURITY SYSTEM FUNCTION.
Check if the room light activates.
CHECK: Does the room light turn on for 30 seconds, and then turn off?
YES: Go to step 6A5.
NO: Replace security control module.
6A5: CHECK SECURITY SYSTEM FUNCTION.
1. Unlock all doors with door locking switch in the front door.
2. Open the front left door.
CHECK: Does the security indicator light blink every 1/8 seconds?
YES: Go to step 6A6.
NO: Go to step 6D1.
6A6: CHECK SECURITY SYSTEM FUNCTION.
Check if the clearance light activates.
CHECK: Does the clearance light blinking remain?
YES: Go to step 6A7.
NO: Replace security control module.
6A7: CHECK SECURITY SYSTEM FUNCTION.
Check if the horn activates.
CHECK: Does the horn sound remain?
YES: Go to step 6A8.
NO: Go to step 6M1.
6A8: CHECK SECURITY SYSTEM FUNCTION.
Turn on starter.
CHECK: Does the starter motor activate?
YES: Go to step 6E1.
NO: Go to step 6A9.
6A9: CHECK SECURITY SYSTEM FUNCTION.
Close the front left door.
CHECK: Does the horn sound and clearance light blinking deactivate, and starter motor activate after approximately 30 seconds?
YES: Go to step 6A10.
NO: Replace security control module.
6A10: CHECK SECURITY SYSTEM FUNCTION.
Check if the security indicator light activates.
CHECK: Does the security indicator light blink every 2 seconds?
YES: Go to step 6A11.
NO: Replace security control module.
6A11: CHECK SECURITY SYSTEM FUNCTION.
Open the front right door.
CHECK: Does the security indicator light blink every 1/8 seconds, the horn sound, the clearance light blink, and the starter motor deactivate?
YES: Go to step 6A12.
NO: Go to step 6F1.
6A12: CHECK SECURITY SYSTEM FUNCTION.
Press the UNLOCK/DISARM button.
CHECK: Does the security indicator light blink, the horn and clearance light deactivate, and the starter motor activate?
YES: Go to step 6A13.
NO: Replace security control module.
6A13: CHECK SECURITY SYSTEM FUNCTION.
1. Close the front right door.
2. Press the LOCK/ARM button.
3. Open the rear left door.
CHECK: Does the security indicator light blink every 1/8 seconds, the horn sound, the clearance light blink, and the starter motor deactivate?
YES: Go to step 6A14.
NO: Go to step 6G1.
6A14: CHECK SECURITY SYSTEM FUNCTION
1. Close the rear left door.
2. Open the rear right door.
CHECK: Does the security indicator light blink every 1/8 seconds, the horn sound, the clearance light blink, and the starter motor deactivate?
YES: Go to step 6A15.
NO: Go to step 6H1.
6A15: CHECK SECURITY SYSTEM FUNCTION.
Close the rear right door.
CHECK: Is the vehicle type wagon?
YES: Go to step 6A16.
NO: Go to step 6A17.
6A16: CHECK SECURITY SYSTEM FUNCTION.
Open the rear gate.
CHECK: Does the security indicator light blink every 1/8 seconds, the horn sound, the clearance light blink, and the starter motor deactivate?
YES: Go to step 6A18.
NO: Go to step 611.
6A17: CHECK SECURITY SYSTEM FUNCTION.
Open the trunk lid.
CHECK: Does the security indicator light blink every 1/8 seconds, the horn sound, the clearance light blink, and the starter motor deactivate?
YES: Go to step 6A18.
NO: Go to step 6J1.
6A18: PERFORM IMPACT SENSITIVITY TEST.
1. Close the rear gate or trunk lid.
2. Close all windows.
3. Cover the hood with a blanket.
4. Perform arming.
5. Perform impact sensitivity test.
CHECK: Does the horn chirp?
YES: Go to step 6A19.
NO: Go to step 6K1.
6A19: CHECK PASSIVE ARM.
1. Remove the driver's side sill cover.
2. Connect the white connector (1-pin) at front pillar lower.
3. Close all doors, rear gate or trunk lid.
CHECK: Does the arming automatically function after 1 minute?
YES: Go to step 6A20.
NO: Go to step 6L1.
6A20: CHECK BATTERY DISCONNECT PROTECTION.
1. Press the UNLOCK/DISARM button.
2. Connect the white connector (1-pin) at front pillar lower.
3. Install the driver's side sill cover.
4. Open the front hood.
5. Press the LOCK/ARM button.
6. Disconnect the ground cable from battery.
7. Connect the ground cable to battery.
CHECK: Does re-arming function automatically?
YES: End of basic diagnostics procedure. Press the UNLOCK/DISARM button, and then close all doors, rear gate or trunk lid. Perform ignition switch position turned LOCK to ON to LOCK.
NO: Replace security control module.