Removal and Installation

A: REMOVAL
1. DISC BRAKE
1. Disconnect ground cable from battery.
2. Jack-up vehicle, and remove rear wheel cap and wheels.

CAUTION: Be sure to loosen and retighten axle nut after removing wheel from vehicle. Failure to follow this rule may damage wheel bearings.

3. Unlock axle nut.
4. Remove axle nut using a socket wrench.
5. Return parking brake lever.





6. Remove ABS sensor.





7. Remove brake caliper from back plate and suspend it from stabilizer using a piece of wire.
8. Remove disc rotor from hub.

NOTE:
^ Before removing disc rotor, mark the matching surface of hub and disc rotor so as not to be confused when installing.
^ If disc rotor seizes up within hub, drive it out by installing an 8 Nm bolt into disc rotor bolt hole.





9. Remove four bolts from rear arm.





10. Remove hub unit bearing.

CAUTION: Be careful not to damage tone wheel.





If it is hard to remove, use STs.
ST1 926470000 AXLE SHAFT PULLER
ST2 927140000 PLATE

2. DRUM BRAKE
1. Disconnect ground cable from battery.
2. Jack-up vehicle, and remove rear wheel cap and wheels.

CAUTION: Be sure to loosen and retighten axle nut after removing wheel from vehicle. Failure to follow this rule may damage wheel bearings.

3. Unlock axle nut.
4. Remove axle nut using a socket wrench.
5. Return parking brake lever.
6. Remove brake drum from hub.





7. If it is difficult to remove brake drum, turn adjusting screw using a slot-type screwdriver until brake shoe separates from the drum.





NOTE: If brake drum is difficult to remove, drive it out by installing an 8-mm bolt into bolt hole in brake drum.





8. Remove ABS sensor.





9. Remove four bolts from rear arm.





10. Remove hub unit bearing.
If it is hard to remove, use STs.
ST1 926470000 AXLE SHAFT PULLER
ST2 927140000 PLATE

CAUTION: Be careful not to damage tone wheel.

B: INSTALLATION
1. DISC BRAKE





1. Align hub unit bearing with back plate at mounting holes and install hub unit assembly and back plate. Temporarily tighten axle nuts.

CAUTION: Be careful not to damage tone wheel.





2. Tighten four bolts to back plate.
3. Remove axle nut.





4. Using ST1 and ST2, pull axle shaft into place.
ST1 922431000 AXLE SHAFT INSTALLER
ST2 927390000 ADAPTER
5. Temporarily tighten axle nuts.
6. Install disc rotor on hub.





7. Install disc brake caliper on back plate.
Tightening torque: 52 Nm (5.3 kgf-m, 38.3 ft. lbs.)





8. Install rear ABS sensor and brake cable bracket.
9. Adjust parking brake lever stroke by turning adjuster.





10. Move brake lever back to apply brakes. While depressing brake pedal, tighten axle nut using a socket wrench. Lock axle nut after tightening.
Tightening torque: 235 Nm (24 kgf-m, 174 ft. lbs.)

CAUTION:
^ Use a new axle nut for rear use only (Olive color).
^ Always tighten axle nut before installing wheel on vehicle. If wheel is installed and comes in contact with ground when axle nut is loose, wheel bearings may be damaged.
^ Be sure to tighten axle nut to specified torque. Do not overtighten it as this may damage wheel bearing.

11. Install wheel and tighten wheel nuts to specified torque.
Tightening torque: 88 Nm (9 kgf-m, 65 ft. lbs.)

2. DRUM BRAKE





1. Align hub unit bearing with back plate at mounting holes and install hub unit assembly and back plate. Temporarily tighten axle nuts.

CAUTION: Be careful not to damage tone wheel.





2. Tighten four bolts to back plate.
3. Remove axle nut.
4. Using ST1 and ST2, pull axle shaft into place.
ST1 922431000 AXLE SHAFT INSTALLER
ST2 927390000 ADAPTER





5. Temporarily tighten axle nuts.





6. Install rear ABS sensor.
Tightening torque: 32 Nm (3.3 kgf-m, 23.9 ft. lbs.)
7. Install brake drum on rear housing assembly.
8. Move brake lever back to apply brakes. While depressing brake pedal, tighten axle nut using a socket wrench. Lock axle nut after tightening.
Tightening torque: 235 Nm (24 kgf-m, 174 ft. lbs.)

CAUTION:
^ Use a new axle nut for rear use only (Olive color).
^ Always tighten axle nut before installing wheel on vehicle. If wheel is installed and comes in contact with ground when axle nut is loose, wheel bearings may be damaged. Be sure to tighten axle nut to specified torque. Do not overtighten it as this may damage wheel bearing.

9. Install wheel and tighten wheel nuts to specified torque.
Tightening torque: 88 Nm (9 kgf-m, 65 ft. lbs.)