Front Differential Assembly
A: REMOVAL1. Remove the manual transmission assembly from vehicle.
2. Remove transfer case with extension case assembly.
3. Remove transmission case.
4. Removes drive pinion shaft assembly. Remove transfer case with extension case assembly.
5. Remove main shaft assembly.
6. Remove differential assembly.
CAUTION:
^ Be careful not to confuse right and left roller bearing outer races.
^ Be careful not to damage retainer oil seal.
7. Remove differential side retainers using ST.
ST 499787000 WRENCH ASSY
B: INSTALLATION
1. Install differential side retainers using ST.
ST 499787000 WRENCH ASSY
2. Install differential assembly.
CAUTION: Be careful not to fold the sealing lip of oil seal.
NOTE: Wrap the left and right splines sections of axle shaft with vinyl tape to prevent scratches.
3. Install main shaft assembly.
4. Install drive pinion assembly.
5. Install transmission case.
6. Install transfer case with extension case assembly.
7. Install the manual transmission assembly to vehicle.
C: DISASSEMBLY
1. Remove right and left snap rings from differential, and then remove two axle drive shafts.
NOTE: During reassembly, reinstall each axle drive shaft in the same place from which it was removed.
2. Loosen twelve bolts and remove hypoid driven gear.
3. Drive out straight pin from differential assembly toward hypoid driven gear.
ST 899904100 REMOVER
4. Pull out pinion shaft, and remove differential bevel pinion and gear and washer.
5. Remove roller bearing using ST.
ST 399527700 PULLER SET
D: ASSEMBLY
1. Install bevel gear and bevel pinion together with washers, and insert pinion shaft.
NOTE: Face the chamfered side of washer toward gear.
2. Measure backlash between bevel gear and pinion. If it is not within specifications, install a suitable washer to adjust it.
NOTE: Be sure the pinion gear tooth contacts adjacent gear teeth during measurement.
ST1 498247001 MAGNET BASE
ST2 498247100 DIAL GAUGE
Standard backlash: 0.13 - 0.18 mm (0.0051 - 0.0071 inch)
3. Align pinion shaft and differential case at their holes, and drive straight pin into holes from the hypoid driven gear side, using ST.
NOTE: Lock straight pin after installing.
ST8 99904100 REMOVER
4. Install roller bearing to differential case.
CAUTION: Do not apply pressure in excess of 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).
NOTE: Be careful to use roller bearing outer races as a set.
ST1 499277100 BUSHING 1-2 INSTALLER
ST2 398497701 ADAPTER
5. Install hypoid driven gear to differential case using twelve bolts.
Tightening torque:
T: 62 Nm (6.3 kgf-m, 45.6 ft. lbs.)
E: INSPECTION
Repair or replace the differential gear in the following cases:
^ The hypoid drive gear and drive pinion shaft tooth surface are damaged, excessively worn, or seized.
^ The roller bearing on the drive pinion shaft has a worn or damaged roller path.
^ There is damage, wear, or seizure of the differential bevel pinion, differential bevel gear, washer, pinion shaft, and straight pin.
^ The differential case has worn or damaged sliding surfaces.
1. BEVEL PINION GEAR BACKLASH
Measure backlash between bevel gear and pinion. If it is not within specifications, install a suitable washer to adjust it.
NOTE: Be sure the pinion gear tooth contacts adjacent gear teeth during measurement.
ST1 498247001 MAGNET BASE
ST2 498247100 DIAL GAUGE
Standard backlash: 0.13 - 0.18 mm (0.0051 - 0.0071 inch)
2. HYPOID GEAR BACKLASH
Set ST1, ST2 and ST3. Insert the needle through transmission oil drain plug hole so that the needle comes in contact with the tooth surface at a right angle and check the backlash.
ST1 498247001 MAGNET BASE
ST2 498247100 DIAL GAUGE
ST3 498255400 PLATE
Backlash: 0.13 - 0.18 mm (0.0051 - 0.0071 inch)
NOTE: If backlash is outside specified range, adjust it by turning holder in right side case.
3. TOOTH CONTACT OF HYPOID GEAR
Check tooth contact of hypoid gear as follows: Apply a uniform thin coat of red lead on both tooth surfaces of 3 or 4 teeth of the hypoid gear. Move the hypoid gear back and forth by turning the transmission main shaft until a definite contact pattern is developed on hypoid gear, and judge whether face contact is correct. If it is inaccurate, make adjustment.
^ Tooth contact is correct.
F: ADJUSTMENT
1. BEVEL PINION GEAR BACKLASH
1. Disassemble the front differential.
2. Select a different washer from the table and install.
3. Adjust until the specified value is obtained.
Standard backlash: 0.13 - 0.18 mm (0.0051 - 0.0071 inch)
2. HYPOID GEAR BACKLASH
Adjust backlash by turning holder in the right side case.
ST4 99787000 WRENCH ASSY
NOTE: Each time holder rotates one tooth, backlash changes by 0.05 mm (0.0020 inch).
3. TOOTH CONTACT OF HYPOID GEAR
Adjust until the teeth contact is correct.
^ Backlash is excessive.
To reduce backlash, loosen holder on the upper side (case right side) and turn in the holder on the lower side (case left side) by the same amount.
^ Backlash is insufficient.
To increase backlash, loosen holder on the lower side (case left side) and turn in the holder on the upper side (case right side) by the same amount.
^ The drive pinion shim selected before is too thick.
Reduce its thickness.
^ The drive pinion shim selected before is too thin. Increase its thickness.