Subaru Select Monitor
HOW TO USE SUBARU SELECT MONITOR
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Insert the cartridge into Subaru Select Monitor.
4. Connect the Subaru Select Monitor to data link connector.
1. The data link connector is located in the lower portion of the instrument panel (on the driver's side).
2. Connect the diagnosis cable to data link connector.
CAUTION: Do not connect scan tools except for Subaru Select Monitor and OBD-II general scan tool.
5. Turn ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
6. Using the Subaru Select Monitor, call up diagnostic trouble code(s) and various data, then record them.
READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE. (NORMAL MODE)
Refer to Read Diagnostic Trouble Code for information about how to indicate DTCs.
READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE. (OBD MODE)
Refer to Read Diagnostic Trouble Code for information about how to indicate DTCs.
READ CURRENT DATA FOR ENGINE. (NORMAL MODE)
1. On the [[Main Menu]] display screen, select {Each System Check} and press the [YES] key.
2. On the [[System Selection Menu]] display screen, select {Engine Control System} and press the [YES] key.
3. Press the [YES] key after the engine type information is displayed.
4. On the [[Engine Diagnosis]] display screen, select {Current Data Display & Save} and press the [YES] key.
5. On the [[Data Display Menu]] display screen select {Data Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.
Part 1:
Part 2:
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
READ CURRENT DATA FOR ENGINE. (OBD MODE)
1. On the [[Main Menu]] display screen, select {Each System Check} and press the [YES] key.
2. On the [[System Selection Menu]] display screen, select {Engine Control System} and press the [YES] key.
3. Press the [YES] key after the engine type information is displayed.
4. On the [[Engine Diagnosis]] display screen, select {OBD System} and press the [YES] key.
5. On the [[OBD Menu]] display screen, select {Current Data Display & Save} and press the [YES] key
6. On the [[Data Display Menu]] display screen, select {Data Display} and press the [YES] key.
7. Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
READ FREEZE FRAME DATA FOR ENGINE. (OBD MODE)
1. On the [[Main Menu]] display screen, select {Each System Check} and press the [YES] key.
2. On the [[System Selection Menu]] display screen, select {Engine Control System} and press the [YES] key.
3. Press the [YES] key after the engine type information is displayed.
4. On the [[Engine Diagnosis]] display screen, select {OBD System} and press the [YES] key.
5. On the [[OBD Menu]] display screen, select {Freeze Frame Data} and press the [YES] key.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
LED OPERATION MODE FOR ENGINE
1. On the [[Main Menu]] display screen, select {Each System Check} and press the [YES] key.
2. On the [[System Selection Menu]] display screen, select {Engine Control System} and press the [YES] key.
3. Press the [YES] key after the engine type information is displayed.
4. On the [[Engine Diagnosis]] display screen, select {Current Data Display & Save} and press the [YES] key.
5. On the [[Data Display Menu]] display screen, select {Data & LED Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
READ CURRENT DATA FOR AT.
1. On the [[Main Menu]] display screen, select {Each System Check} and press the [YES] key.
2. On the [[System Selection Men]] display screen, select the {Transmission Control System} and press the [YES] key.
3. Press the [YES] key after the transmission type information is displayed.
4. On the [[Transmission Diagnosis]] display screen, select {Current Data Display & Save} and press the [YES] key.
5. On the [[Data Display Menu]] display screen, select {Data Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.