Assembly
Rear DifferentialASSEMBLY
NOTE:
^ Assemble in the reverse order of disassembling.
^ Check and adjust each part during assembly.
^ Keep the shims and washers in order, so that they are not misinstalled.
^ Thoroughly clean the surfaces on which the shims, washers and bearings are to be installed.
^ Apply gear oil when installing the bearings and thrust washers.
^ Be careful not to mix up the right and left hand races of the bearings.
^ Replace the oil seal with a new one at every disassembly. Apply chassis grease between the lips when installing the oil seal.
^ Be careful not to mix up right and left oil seals.
1) If the air breather cap was removed, install it by tapping with a plastic hammer.
CAUTION: Use a new air breather cap.
2) Adjusting preload for front and rear bearings:
Adjust the bearing preload with spacer and washer between front and rear bearings. Pinion height adjusting washer are not affected by this adjustment. The adjustment must be carried out without oil seal inserted.
1) Press the rear bearing race (rear) into differential carrier with ST1 and ST2.
ST1 398477701 HANDLE
ST2 398477703 DRIFT 2
2) Install the rear bearing race (front) into differential carrier with ST1 and ST2.
ST1 398477701 HANDLE
ST2 398477702 DRIFT
3) Insert the ST1 into carrier with pinion height adjusting washer and rear bearing cone fitted onto it.
CAUTION:
^ If the tooth contact (between drive pinion and crown gear) was normal at the check prior to disassembly, check that the used washer is not deformed and reuse it.
^ Use a new rear bearing cone.
4) Then install the preload adjusting spacer and washer, front bearing cone, ST2, companion flange, and washer and drive pinion nut.
ST1 398507702 DUMMY SHAFT
ST2 398507703 DUMMY COLLAR
5) Turn the ST1 with hand to make it seated, and tighten the drive pinion nut while measuring the preload with spring balance. Select the preload adjusting washer and spacer so that the specified preload is obtained when nut is tightened to the specified torque.
CAUTION: Use a new lock nut.
NOTE:
^ Be careful not to give excessive preload.
^ Take measurement in a tangential line to the flange.
^ When tightening the drive pinion nut, lock ST1 with ST2 as shown in the figure.
ST1 398507704 BLOCK
ST2 398507702DUMMY SHAFT
Tightening torque: 181 Nm (18.5 kgf-m, 134 ft. lbs.)
3) Adjusting drive pinion height:
Adjust the drive pinion height with shim installed between rear bearing cone and the back of pinion gear.
1) Leave ST1, ST2 and ST3 as they were when the preload adjustment has been completed.
Adjusting preload for front and rear bearings:
NOTE: At this time, install a pinion height adjusting shim which is temporarily selected or the same as that used before. Measure and record the thickness.
ST1 398507702 DUMMY SHAFT
ST2 398507701 DIFFERENTIAL CARRIER GAUGE
ST3 398507703 DUMMY COLLAR
2) Measure the clearance N between the end of ST2 and the end surface of ST1 by using a thickness gauge.
NOTE: Make sure there is no clearance between the case and ST2.
ST1 398507702 DUMMY SHAFT
ST2 398507701 DIFFERENTIAL CARRIER GAUGE
3) Obtain the thickness of pinion height adjusting shim to be inserted from the following formula, and replace the temporarily installed shim with this one.
T = To + N - (H x 0.01) - 0.20 mm (0.0079 inch)
NOTE: Use copies of this page.
(Example of calculation)
To = 2.20 + 1.20 = 3.40 mm
N = 0.23 mm H =+ 1.
T=3.40+0.23-0.01 -0.20 = 3.42
Result: Thickness = 3.42 mm Therefore use the shim 383605200.
4) Install the selected pinion height adjusting shim on drive pinion, and press the rear bearing cone into position with ST.
ST3 98177700 INSTALLER
5) Insert the drive pinion into differential carrier, install the previously selected bearing preload adjusting spacer and washer.
6) Press-fit the front bearing cone into case with ST1, ST2 and ST3.
ST1 398507703 DUMMY COLLAR
ST2 399780104 WEIGHT
ST3 899580100 INSTALLER
7) Insert the spacer, then press-fit pilot bearing with ST1 and ST2.
ST1 399780104 WEIGHT
ST2 899580100 INSTALLER
8) Fit a new oil seal with ST.
NOTE:
^ Press-fit until end of oil seal is 1 mm (0.04 inch) inward from end of carrier.
^ Apply grease between the oil seal lips.
ST 498447120 INSTALLER
9) Press-fit the companion flange with ST1 and ST2.
CAUTION: Be careful not to damage the bearing.
ST1 899874100 INSTALLER
ST2 399780104 WEIGHT
10) Install the self-locking nut. Then tighten it with ST.
ST 498427200 FLANGE WRENCH
CAUTION: Use new lock nut.
Tightening torque: 181 Nm (18.5 kgf-m, 134 ft. lbs.)
11) Assembling differential case: Install the side gears and pinion mate gears, with their thrust washers and pinion mate shaft, into differential case. (Without LSD)
CAUTION:
^ Apply gear oil on both sides of the washer and on the side gear shaft before installing.
^ Insert the pinion mate shaft into the differential case by aligning the lock pin holes.
1) Measure the side gear backlash.
Side gear back clearance: 0.10 - 0.20 m m (0.0039 - 0.0079 inch)
2) Adjust the backlash as specified by selecting side gear thrust washer.
3) Check the condition of rotation after applying oil to the gear tooth surfaces and thrust surfaces.
4) After inserting the pinion shaft lock pin into differential case, stake the both sides of the hole to prevent pin from falling off.
12) Install the crown gear on differential case.
CAUTION: Before installing bolts, apply thread lock to bolt threads.
Lock Tote: THREE BOND 1324 (Part No. 004403042) or equivalent
NOTE: Tighten diagonally while tapping the bolt heads.
Tightening torque: 103 Nm (105 kgf-m 7 ft. lbs.)
13) Press the side bearing cone onto differential case with ST.
ST3 98487700 DRIFT
14) Adjusting the side bearing retainer shims:
1) The driven gear backlash and side bearing preload can be determined by the side bearing retainer shim thickness.
2) Install the differential case assembly into differential carrier in the reverse order of disassembly.
3) Install the side retainer shims and O-rings to the left and right retainers from which they were removed.
NOTE:
^ Replace the broken or cracked O-ring with a new one.
^ Replace the broken or corroded side retainer shim with a new one of same thickness.
4) Align the arrow mark on differential carrier with that marked on side retainer during installation.
CAUTION: Be careful that side bearing outer race is not damaged by bearing roller.
5) Tighten the side bearing retainer bolts.
CAUTION: Before tightening the two side bearing retainer bolts, apply thread lock to bolt threads.
Thread lock: THREE BOND 1105 (Part No. 004403010) or equivalent
Tightening torque: 10.3 Nm (1.05 kgf-m, 7.6 ft. lbs.)
Fig. 15 Measuring Backlash:
6) Measure the crown gear-to-drive pinion backlash. Set the magnet base on differential carrier. Align the contact point of dial gauge with tooth face of crown gear, and move crown gear while holding drive pinion still. Read the value indicated on dial gauge.
Backlash: 0.10 - 0.20 mm (0.0039 - 0.0079 inch)
If the backlash is not within the specified range, adjust the side retainer shims as follows:
Backlash over 0.2 mm (0.0079 inch): Lessen thickness of shims at crown gear back side and add thickness of shims at crown gear teeth side.
Backlash under 0.1 mm (0.0039 inch):
Add thickness of shims at crown gear back side and lessen thickness of shims at crown gear teeth side.
7) At the same time, measure the turning resistance of drive pinion. Compared with the resistance when differential case is not installed, if the increase of the resistance is not within the specified range, readjust side bearing retainer shims by adding/removing same amount of shims at both sides.
Turning resistance increase: 2.9 - 10.8 N (0.3 - 1.1 kgf, 0.7 - 2.4 lbs.)
Fig. 15 Measuring Backlash:
15) Recheck the crown gear-to-pinion backlash.
Backlash: 0.10 - 0.20 mm (0.0039 - 0.0079 inch)
Fig. 16 Measuring Runout:
16) Check the crown gear runout on its back surface, and make sure pinion and crown gear rotates smoothly.
Limit of runout: Less than 0.05 mm (0.0020 inch)
17) Checking and adjusting the tooth contact of crown gear:
1) Apply an even coat of red lead on both sides of three or four teeth on the the crown gear. Check the contact pattern after rotating the crown gear several revolutions back and forth until a definite contact pattern appears on the crown gear.
2) When the contact pattern is incorrect, readjust according to the instructions given in "TOOTH CONTACT PATTERN".
NOTE: Be sure to wipe off red lead completely after adjustment is completed.
18) If proper tooth contact is not obtained, once again adjust the drive pinion height changing RH and LH side bearing retainer shims and the hypoid gear backlash.
1) Drive pinion height
ST1 398507702 DUMMY SHAFT
ST2 398507701 DIFFERENTIAL CARRIER GAUGE
T= To+ N - (H x0.01) - 0.20 (mm)
Where:
T = Thickness of pinion height adjusting shim (mm)
To = Thickness of shim temporarily inserted (mm)
N = Reading of thickness gauge (mm)
H = Figure marked on drive pinion head
Fig. 15 Measuring Backlash:
2) Hypoid gear backlash
Backlash: 0.10 - 0.20 mm (0.0039 - 0.0079 inch)
19) Remove left and right side bearing retainers.
20) Install left and right bearing retainer O-rings and side bearing retainer shims.
21) Install oil seal on left and right side bearing retainers.
22) At installation, align arrow mark on differential carrier with arrow mark on side retainer.
23) Tighten side bearing retainer bolts.
Thread lock: THREE BOND 1105 (Part No. 004403010) or equivalent
Tightening torque: 10.3 Nm (1.05 kgf-m, 7.6 ft. lbs.)
24) Install the rear cover and tighten bolts to specified torque.
CAUTION: Securely connect the ground terminal of rear differential temperature sensor.
Tightening torque: 29 Nm (3.0 kgf-m, 21.7 ft. lbs.)