Subaru Select Monitor
HOW TO USE SUBARU SELECT MONITOR
1. Prepare Subaru Select Monitor kit.
2. Connect diagnosis cable to Subaru Select Monitor.
3. Insert cartridge into Subaru Select Monitor.
4. Connect Subaru Select Monitor to data link connector.
1. Data link connector (A) located in the lower portion of the instrument panel (on the driver's side).
2. Connect diagnosis cable to data link connector.
CAUTION: Do not connect scan tools except for Subaru Select Monitor and OBD-II general scan tool.
5. Turn ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
6. Using Subaru Select Monitor, call up diagnostic trouble code(s) and various data, then record them.
READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE. (NORMAL MODE)
Refer to Read Diagnostic Trouble Code for information about how to indicate DTC.
READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE. (OBD MODE)
Refer to Read Diagnostic Trouble Code for information about how to indicate DTC.
READ CURRENT DATA FOR ENGINE. (NORMAL MODE)
1. On the Main Menu display screen, select the {Each System Check} and press the [YES] key.
2. On the System Selection Menu display screen, select the {Engine Control System) and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the Engine Diagnosis display screen, select the {Current Data Display & Save} and press the [YES] key.
5. On the Data Display Menu display screen, select the {Data Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.
Part 1:
Part 2:
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
READ CURRENT DATA FOR ENGINE. (OBD MODE)
1. On the Main Menu display screen, select the {Each System Check} and press the [YES] key.
2. On the System Selection Menu display screen, select the {Engine Control System} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the Engine Diagnosis display screen, select the {OBD System} and press the [YES] key.
5. On the OBD Menu display screen, select the {Current Data Display & Save} and press the [YES] key.
6. On the Data Display Menu display screen, select the {Data Display} and press the [YES] key.
7. Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
READ FREEZE FRAME DATA FOR ENGINE. (OBD MODE)
1. On the Main Menu display screen, select the {Each System Check} and press the [YES] key.
2. On the System Selection Menu display screen, select the {Engine Control System} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the Engine Diagnosis display screen, select the {OBD System} and press the [YES] key.
5. On the OBD Menu display screen, select the {Freeze Frame Data} and press the [YES] key.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
LED OPERATION MODE FOR ENGINE
1. On the Main Menu display screen, select the {Each System Check} and press the [YES] key.
2. On the System Selection Menu display screen, select the {Engine Control System} and press the [YES] key.
3. Press the [YES] key after displayed the information of engine type.
4. On the Engine Diagnosis display screen, select the {Current Data Display & Save} and press the [YES] key.
5. On the Data Display Menu display screen, select the {Data & LED Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
READ CURRENT DATA FOR AT.
1. On the Main Menu display screen, select the {Each System Check} and press the [YES] key.
2. On the System Selection Menu display screen, select the {Transmission Control System} and press the [YES] key.
3. Press the [YES] key after displayed the information of transmission type.
4. On the Transmission Diagnosis display screen, select the {Current Data Display & Save} and press the [YES] key.
5. On the Data Display Menu display screen, select the {Data Display} and press the [YES] key.
6. Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.