Front Seat
Front SeatDISASSEMBLY
1. STANDARD
1. Remove seats from vehicle.
2. Remove lumber lever cover.
3. Remove hook at bottom, and then remove seat back board.
4. Remove hook on back side of seat, and remove hog rings using a plier.
5. Remove clamp of side airbag wire harness. (Side airbag equipped vehicle)
6. Remove clamp of seat heater wire harness. (Seat heater equipped vehicle)
7. Turn cover and cushion, and remove the two bolts from hinge.
8. Remove hinge screw cover and screws, and remove seat back from hinge.
9. While picking up tip with a plier, remove headrest lock bushing.
10. Remove hog ring (A) on front face of seat.
Side airbag equipped vehicle:
NOTE: Backrest portion of side airbag equipped vehicle cannot be disassembled. When disposing of it, refer to the following.
CAUTION: After disassembly of the parts, for side airbag performance assurance reasons, do not assemble and re-use the parts. When replacing it, replace with a complete backrest assembly.
11. Remove hog rings, and then remove seat heater. (Seat heater equipped vehicle)
12. Remove seat cover.
13. Remove backrest pad.
14. Remove clamp of airbag wire harness on back side of seat. (Side airbag equipped vehicle)
15. Remove the two cap nuts, and then remove side airbag module assembly. (Side airbag equipped vehicle)
16. Remove reclining cover and hinge cover. (Non-tilt type vehicle)
17. Remove the 4 bolts of seat hinge assembly, and then remove seat cushion.
Tilt type vehicle:
Non-tilt type vehicle:
18. Remove hook clips on back side of seat cushion, and remove wire rings.
19. Remove clamp of seat heater wire harness. (Seat heater equipped vehicle)
20. Remove hog rings (A).
Tilt type vehicle:
Non-tilt type vehicle:
Leather type vehicle:
21. Remove cushion cover.
22. Remove cushion pad.
23. Remove clip pins, and remove seat lifter lever.
24. Remove reclining lever cover.
25. Remove hinge cover cap and screws.
26. Remove seat hinge cover and hinge spring cover.
27. Remove 2 bolts, and then remove slide rail.
28. Remove 4 screws, and then remove hinge. (Non-tilt type vehicle)
29. Remove 2 bolts, and then remove slide rail. (Non-tilt type vehicle)
30. Remove connecting wire.
2. POWER
1. Remove seats from vehicle.
2. Remove lumber lever cover.
3. Remove hook at bottom, and then remove seat back board.
4. Remove hook on back side of seat, and remove wire rings using a plier.
5. Remove clamp of side airbag wire harness. (Side airbag equipped vehicle)
6. Remove clamp of seat heater wire harness. (Seat heater equipped vehicle)
7. Turn cover and cushion, and remove the two bolts from hinge.
8. Remove hinge screw cover and screws, and remove seat back from hinge.
9. While picking up tip with a plier, remove headrest lock bushing.
10. Remove hog ring (A) on front face of seat.
Side airbag equipped vehicle:
NOTE: Backrest portion of side airbag equipped vehicle cannot be disassembled. When disposing of it, refer to the following.
CAUTION: After disassembly of the parts, for side airbag performance assurance reasons, do not assemble and re-use the parts. When replacing it, replace with a complete backrest assembly.
11. Remove wire rings, and then remove seat heater. (Seat heater equipped vehicle)
12. Remove seat cover.
13. Remove backrest pad.
14. Remove clamp of airbag wire harness on back side of seat. (Side airbag equipped vehicle)
15. Remove the two cap nuts, and then remove side airbag module assembly. (Side airbag equipped vehicle)
16. Remove the 4 bolts of seat hinge assembly, and then remove seat cushion.
17. Remove hook clips on back side of seat cushion, and remove wire rings.
18. Remove clamp of seat heater wire harness. (Seat heater equipped vehicle)
19. Remove hog rings (A).
Leather type vehicle:
20. Remove cushion cover.
21. Remove cushion pad.
22. Remove the screw and then remove the cover.
23. 8-way power:
Remove the screw, disconnect the seat switch connector on the underside of the cover, and remove the hinge cover.
6-way power:
Remove the reclining lever cover and screw, disconnect the seat switch connector on the underside of the cover, and remove the hinge cover.
24. Remove the cover on the underside of the seat hinge, remove the two bolts, and remove the seat hinge.
ASSEMBLY
1. STANDARD
1. Assemble in the reverse order of disassembly.
NOTE:
- Do not contaminate or damage cover.
- While installing hog rings, prevent seat from getting wrinkled.
2. Attach seat cover end hole to hinge inner. (Only non-tilt type standard seat)
2. POWER
1. Assemble in the reverse order of disassembly.
NOTE:
- Do not contaminate or damage cover.
- While installing hog rings, prevent seat from getting wrinkled.
- Make sure the connector is firmly connected.
- Make sure the wire harness is not pinched.
2. Attach seat cover end hole to hinge inner. (Only non-tilt type standard seat)