P0457
DTC P0457 - EVAPORATIVE EMISSION CONTROL SYSTEM LEAK DETECTED (FUEL CAP LOOSE/OFF)OUTLINE OF DIAGNOSIS
In this system diagnosis, checking for leakage and valve function is conducted by changing the fuel tank pressure, and monitoring the pressure change using the fuel tank pressure sensor. 0.04 inch diagnosis is performed in the order of mode Z, mode A, mode B, mode C, mode D and mode E, and 0.02 inch diagnosis is performed in the order of mode Y, mode A, mode B, mode C, mode D and mode E.
- 0.04-inch Diagnosis
- 0.02-inch Diagnosis
- Mode Table for Evaporative Emission Control System Diagnosis
COMPONENT DESCRIPTION
- Pressure Control Solenoid Valve
PCV controls the fuel tank pressure to be equal to the atmospheric air pressure.
Normally, the solenoid is set to OFF. And the valve opens and closes mechanically in accordance with the pressure difference between tank and atmospheric air, or tank and canister.
Also the valve is able to forcibly opened by setting the solenoid to ON.
- Valve Operation and Air Flow
In the figure, divided by the diaphragm, the part above X is charged with atmospheric air pressure, and the part below X is charged with tank pressure. Also, the part above Y is charged with tank pressure, and the part below Y is charged with canister pressure.
If the atmospheric air pressure port is A, tank pressure port is B, and canister pressure port is C, the air flows according to pressure difference from each port as shown in the table.
- When A < B (Solenoid OFF)
- When B < C (Solenoid OFF)
- When Solenoid is ON
- CCV
In normal condition, drain valve opens when solenoid is turning OFF, and the solenoid is turned ON when diagnosis and the valve close.
- Tank Pressure Switching Solenoid
- Purpose of this solenoid
Fuel tank pressure sensor detects the difference between the atmospheric air pressure and the tank pressure and the ECM monitors the pressure difference.
Even if the tank pressure is constant, the atmospheric air pressure varies depending on the driving height, and the pressure signal transmitted to ECM will change.
Especially, in the small leakage [0.5 mm (0.02 in)], minute change in the tank pressure has to be detected. This diagnosis period is long (approx. 29 seconds). And if the driving height changes during the diagnosis, the atmospheric air pressure changes. In this case, it becomes difficult to precisely detect the tank pressure variation, causing erroneous diagnosis. Therefore, using the atmospheric pressure switching solenoid, atmospheric air is sealed between the fuel tank pressure sensor and atmospheric pressure switching solenoid, maintaining the air pressure constant and enabling the detection of minute variation of tank pressure.
NOTE: ECM also has the atmospheric air pressure sensor, and always monitors atmospheric air. However, as the monitoring range is large, that is, 53 to 107 kPa (400 to 800 mmHg, 16 to 32 inHg) it is not suitable for detection of minute pressure variation.
In the case of small leakage diagnosis, the tank pressure variation is very small, that is, 0.13 to 0.27 kPa (1 to 2 mmHg, 0.04 to 0.08 inHg) and the fuel tank pressure sensor is equipped.
ENABLE CONDITION
GENERAL DRIVING CYCLE
- 0.04-inch Diagnosis
- Perform the diagnosis only once in more than 454 seconds after the engine start at the constant driving speed of 48 km/h (30 MPH) or more.
- Pay attention to the fuel temperature and fuel level.
- 0.02-inch Diagnosis
- Perform diagnosis in more than 325 seconds after engine start at the constant speed of 68 km/h (42 MPH) or more, and then terminate the diagnosis when judged OK or NG.
- If not judged OK or NG, repeat the diagnosis until judged OK or NG.
- Pay attention to the fuel temperature and fuel level.
DIAGNOSTIC METHOD
- MODE Y (Tank pressure stabilization)
Perform the diagnosis under the conditions, and return the tank pressure to atmosphere.
Tank pressure > 0.9 kPa (67.5 mmHg, 2.7 inHg) after 0.1 seconds.
Cancel the leak check. (Change to Mode A, Tank pressure <= 0.9 kPa (67.5 mmHg, 2.7 inHg).)
- MODE Z (Purge control solenoid valve open malfunction diagnosis, CPC close malfunction diagnosis)
DTC P0457
DTC P1443
- Purpose of Mode Z
When performing the leakage diagnosis of EVAP system, CCV and CPC have to operate normally. Therefore, mode Z is used to diagnose the CCV close fixation and CPC open fixation.
If the CCV closed fixation trouble or CPC open fixation trouble is detected, the EVAP system leakage diagnosis is cancelled.
If the CCV closed fixation trouble occurred, negative pressure is generated from the engine to pressure control solenoid valve when pressure control solenoid valve is closed and CPC is opened. Under this condition, the valve cannot be opened for the pressure control solenoid valve structure if the negative pressure is larger than electromagnetic force when pressure control solenoid valve solenoid is set to ON in order to open the valve.
- DIAGNOSTIC METHOD
CCV closed fixation diagnosis and CPC open fixation diagnosis are performed in mode Z as shown in the figure.
- Normal Operation
- Drain valve close fixation
- Diagnosing Function of CCV [P1443]
CCV functional diagnosis is performed by monitoring the tank pressure variation in Mode Z.
Normality Judgment
Judge OK and change to Mode A when the criteria are completed in 3 seconds after Mode Z started.
Abnormality Judgment
If OK judgment cannot be made, extend Mode Z 16 seconds more, and judge NG when all the criteria are completed in 16 seconds.
Finish the evaporative emission control system diagnosis when making NG judgment for drain valve close fixation.
Cancel the evaporative emission control system diagnosis when the OK/NG judgment for drain valve close fixation and purge control solenoid valve open fixation cannot be made in Mode Z.
- Leak Diagnosis
DTC P0442
DTC P0456
DTC P0457
- DIAGNOSTIC METHOD
- The diagnostic method consists of creating a sealed vacuum in the fuel tank and then determining the presence of leakage from the speed at which the tank internal pressure returns to atmospheric pressure.
- The diagnosis is divided into the following five phases.
Mode A:
Calculate the tank pressure variation amount (P1) in Mode A. After calculating P1, change to Mode B.
Mode B:
Introduce the negative pressure in the intake manifold to the tank.
Approx. 0 -> -1.4 kPa (0 -> -10.5 mmHg, 0 -> -0.41 inHg) (0.04-in diagnosis)
Approx. 0 -> -3.05 kPa (0 -> -22.9 mmHg, 0 -> -0.9 inHg) (0.02-in diagnosis)
When the pressure above (desired negative pressure) is reached, Mode C is entered.
In this case, if the tank pressure does not become the desired negative pressure, judge that there is a large leakage in the system.
Judge NG when the malfunction criteria is completed.
Finish the Evap. diagnosis when judging large leak (35 seconds) in 0.04-inch diagnosis. Cancel the diagnosis (62 seconds) in 0.02-inch diagnosis.
Abnormality Judgment
Judge NG (large leak) when the criteria are completed in the specified time.
Specified Time
High vehicle speed mode (Vehicle speed >= 72 km/h (45 MPH)); 35 seconds
Low vehicle speed mode (Vehicle speed < 72 km/h (45 MPH)); 18 seconds
Mode C:
Stop the introduction of negative pressure. (Wait until the tank pressure returns to the start level of P2 calculation.)
Change to Mode D when the tank pressure returns to the start level of P2 calculation.
Judge immediate OK and change to Mode E when it does not return in spite of spending the specified time.
Mode D:
Monitor the pressure variation in the tank in Mode D. In this case, the tank pressure increases, that is, the pressure becomes as high as the atmospheric air pressure, because evaporator is generated. However, if any leakage exists, the pressure increases additionally in proportion to this leakage. The pressure variation of this tank is P2.
After calculating P2, perform small leak diagnosis and change to Mode E if normal. Complete Evap. diagnosis if abnormal.
- After Diagnosis
Assigning P1 and P2, which are tank variations measured in Mode A and Mode B, to the formula below, judge the small leakage of the system. If the measured judgment value exceeds the threshold value, it is judged to be malfunction.
- 0.04-inch Diagnosis
Abnormality Judgment
Judge NG when the criteria are completed and judge OK when not completed.
- 0.02-inch Diagnosis
Abnormality Judgment
Judge NG when the criteria are completed.
Normality Judgment
Judge OK when the criteria are completed.
If not judged OK or NG, repeat the diagnosis.
- CCV Property Diagnosis [P1443]
Mode E:
The tank pressure must become again as high as the atmospheric air pressure after the evaporation diagnosis. If the tank pressure does not become as high as the atmospheric air pressure, judge that CCV is blocked.
DTC CLEAR CONDITION
- When the OK idling cycle was completed 40 times in a row
- When "Clear Memory" was performed
MALFUNCTION INDICATOR LIGHT CLEAR CONDITION
- When the OK driving cycle was completed 3 times in a row
- When "Clear Memory" was performed
FAIL SAFE
Atmospheric purge solenoid function malfunction; Open the pressure control solenoid valve.
ECM OPERATION AT DTC SETTING
- Memorize the freeze frame data. (For test mode $02)
- Memorize the diagnostic value and trouble standard value. (For test mode $06)