P0456
DTC P0456 EVAPORATIVE EMISSION CONTROL SYSTEM LEAK DETECTED (VERY SMALL LEAK)1. OUTLINE OF DIAGNOSIS
Perform the diagnosis of leakage of fuels system and valve functions.
In this system diagnosis, checking for leakage and valve operation is conducted by changing the fuel tank pressure, and monitoring the pressure change using the fuel tank pressure sensor. 0.04 inch diagnosis is performed in the order of Mode Z, Mode A, Mode B, Mode C, Mode D, and 0.02 inch diagnosis is performed in the order of Mode A, Mode B, Mode C, Mode D, Mode E.
0.04-inch Diagnosis
Mode table for Evaporative Emission Control System diagnosis
0.02-inch Diagnosis
2. COMPONENT DESCRIPTION
- Pressure Control Solenoid Valve
PCV controls the fuel tank pressure to be equal to the atmospheric air pressure. Normally, the solenoid is set to OFF, and the valve mechanically opens and closes in accordance with the difference between the tank pressure and atmospheric air pressure, and the tank pressure and canister pressure.
During the diagnosis, the valve is forcibly opened by setting the solenoid to ON.
- Valve Operation and Air Flow
As in the X parts below, there are the area with atmospheric air pressure above the diaphragm and the area with tank pressure below the diaphragm. Also, as in the Y parts below, there are the area with tank pressure above the diaphragm and the area with canister pressure below the diaphragm. In the table the air flow from each port in accordance with pressure difference is shown with the atmospheric air pressure port A, tank pressure port B and canister pressure port C.
When A < B (Solenoid OFF)
When B < C (Solenoid OFF)
When solenoid is ON
- Drain valve
Drain valve controls the ambient air to be introduced to the canister.
3. ENABLE CONDITION
4. GENERAL DRIVING CYCLE
- 0.04-inch Diagnosis
- Perform the diagnosis only once in 856 seconds or more after starting the engine constantly at 32 km/h (19.9 MPH) or more.
- Pay attention to the fuel temperature and fuel level.
- 0.02-inch Diagnosis
- Perform the diagnosis in 770 seconds after starting the engine constantly at 68 km/h (42 MPH) or more, and perform OK/NG judgment.
- If OK/NG judgment is not possible, repeat the diagnosis.
- Pay attention to the fuel temperature and fuel level.
5. DIAGNOSTIC METHOD
- 0.04-inch Diagnosis
Purpose of Mode Z
When performing the leakage diagnosis of EVAP system, and CPC have to operate normally. Therefore, mode Z is used for monitoring the tank pressure to diagnose the CPC open fixation.
If the CPC open fixation trouble is detected, the evaporation system leakage diagnosis is cancelled.
- Diagnosing The CPC Open Fixation
DTC
P0457 Evaporative Emission Control System Leak Detected (Fuel Cap Loose/Off)
CPC open fixation diagnosis are performed in mode Z as shown in the figure.
- Diagnosing function of CPC
DTC
P0457 Evaporative Emission Control System Leak Detected (Fuel Cap Loose/Off)
CPC functional diagnosis is performed by monitoring the tank pressure in Mode Z.
Normality Judgment
Make OK judgment in 3 seconds after Mode Z started, and change to Mode A if OK.
- Normal Operation
Abnormality Judgment
If OK judgment cannot be made, extend Mode Z 16 seconds more, and judge NG when all the criteria are completed in 16 seconds.
Finish the Evap. diagnosis when making NG judgment for purge control solenoid valve open fixation.
Cancel the Evap. diagnosis when the OK/NG judgment for drain valve close fixation and purge control solenoid valve open fixation cannot be made in Mode Z.
- Leak Diagnosis
DTC
P0442 Evaporative Emission Control System Leak Detected (Small Leak)
P0457 Evaporative Emission Control System Leak Detected (Fuel Cap Loose/Off)
- Diagnostic method
The diagnostic method consists of creating a sealed vacuum in the fuel tank and then determining the presence of leakage from the speed at which the tank internal pressure returns to atmospheric pressure.
Mode A: (Estimation of evaporation gas yield)
The amount of change of tank pressure (P1) in Mode A is calculated. After calculating P1, change to Mode B.
Mode B: (Seal negative pressure)
Introduce the negative pressure in the intake manifold to the tank.
Approx. 0 -> -1.4 kPa (0 -> -10.5 mmHg, 0 -> 0.41 in Hg)
When the pressure above (desired negative pressure) is reached, Mode C is entered.
In this case, if the tank pressure does not become the desired negative pressure, judge that there is a large leakage in the system and judge as large leak (10 or 25 seconds).
Abnormality Judgment
Judge NG (large leak) when the criteria are completed in the specified time.
Mode C: (Check increasing pressure)
Stop the introduction of negative pressure. (Wait until the tank pressure returns to the start level of P2 calculation.)
Change to Mode D when the tank pressure returns to the start level of P2 calculation.
Judge immediate OK and change to Mode E when it does not return in spite of spending the specified time.
Mode D: (Measurement of negative pressure changes)
Monitor the pressure variation in the tank in Mode Z. In this case, the tank pressure increases, that is, the pressure becomes as high as the atmospheric air pressure, because evaporator is generated. However, if any leakage exists, the pressure increases additionally in proportion to this leakage. The pressure variation of this tank is P2.
After calculating P2, perform following small leak diagnosis.
- After Mode D
Assigning P1 and P2, which are tank variations measured in Mode A and Mode B, to the formula below, judge the small leakage of the system. If the measured judgment value exceeds the threshold value, it is judged to be malfunction.
Judge NG when the criteria are completed and judge OK when not completed.
- 0.02-inch Diagnosis
DTC
P0456 Evaporative Emission Control System (Very Small Leak)
- Diagnostic method
The diagnostic method consists of creating a sealed vacuum in the fuel tank and then determining the presence of leakage from the speed at which the tank internal pressure returns to atmospheric pressure.
Mode A: (0 point correction)
Wait until the tank pressure returns to 0 point (0 kPa (0 mmHg, 0 inHg)) when the tank pressure is high. Change to Mode B when the tank pressure becomes 0. Cancel the diagnosis when the tank pressure does not return to 0 point in spite of spending the specified time.
Mode B: (Introduce negative pressure)
Introduce the intake manifold negative pressure to fuel tank.
About -> -2.0 kPa (0 mmHg-> -15 mmHg, 0 -> -0.59 inHg)
Change to Mode C when the tank pressure becomes the pressure (desired negative pressure) above. Cancel the diagnosis when the tank pressure does not become the value above.
Mode C: (Hold negative pressure)
Stop introducing the negative pressure and wait the tank pressure returns to the start level of P2 calculation.
Change to Mode D when the tank pressure returns to the start level of P2 calculation or when spending the specified time.
Mode D: (Calculation of negative pressure variation)
Monitor the tank pressure on Mode D, and calculate the tank pressure variation (P2) and time until it returns to the end level of P2 (evpdset). When it returns, change to Mode E. Make advanced OK judgment or cancel depending on the P2 level, when it doesn't return in spite of spending the specified time.
Judge OK when the criteria are completed.
Mode E: (Calculation of evaporation gas yield)
Calculate the tank pressure variation P1 in time evpdset, judge NG/OK from P1 value. (Gray judgment possible)
Abnormal judgment
Judge NG when the criteria are completed.
Normality Judgment
Judge OK when all the malfunction criteria are completed.
6. DTC CLEAR CONDITION
- When the OK idling cycle was completed 40 times in a row
- When "Clear Memory" was performed
7. MALFUNCTION INDICATOR LIGHT CLEAR CONDITION
- When the OK driving cycle was completed 3 times in a row
- When "Clear Memory" was performed
8. FAIL SAFE
None
9. ECM OPERATION AT DTC SETTING
- Memorize the freeze frame data. (For test mode $02)
- Memorize the diagnostic value and trouble standard value. (For test mode $06)