Driver's Seat

Front Seat

DISASSEMBLY

DRIVER'S SEAT

MANUAL SEAT
1. Remove the seat from vehicle.




2. Remove the seat lifter cover using a flat tip screwdriver and loosen the inner bolt to remove seat lifter lever.




3. Remove the hook (A) and detach reclining lever cover.




4. Remove the screws (A) and clips (B), and then detach the seat side cover outside.




5. Loosen the screws to detach seat side cover inside.




6. Remove the TORX(R) bolt, and then remove the inner seat belt assembly.




7. Remove the two bolts from reclining hinge on each side.




8. Remove the clips and hooks, and then detach the backrest back cover.




9. Remove the lock clip, and then remove the lumber support lever.




10. Remove the hooks at the rear side of backrest.




11. Remove the hog rings (A) in the side airbag module installation side.




12. Remove the cover frame (A).




13. Remove the headrest lock bushing.

NOTE: Push outside to remove it from the inside of seat.

14. Pull out the backrest frame assembly.




15. Remove the hog rings (A) on the front side of backrest, and then remove the backrest cover from backrest.




16. Remove the hooks (A), and then remove the seat cushion frame assembly.




17. Remove the hog rings (A), and then remove the seat cushion cover from seat cushion pad.




18. Remove the bolt of sliding adjustment bar and connecting wire.




19. Remove the bolts, and then remove the slide rail.




20. Remove the hooks and hog rings at the bottom of headrest, and then remove the headrest cover from headrest.

POWER SEAT

1. Remove the seat from vehicle.




2. Remove the seat switch knob.




3. Disconnect the connector of reclining motor from the back of seat cushion.




4. Remove the screw (A) and clips (B), and then disconnect the seat switch connector to remove seat side cover outside.




5. Remove the screw (A) and clip (B), and then remove the seat side cover inside.




6. Remove the TORX(R) bolt, and then remove the inner seat belt assembly.




7. Remove the two bolts from the reclining hinge on each left and right side.




8. Remove the clips and hooks, and then detach the backrest back cover.




9. Remove the lock clip, and then remove the lumber support lever.




10. Remove the hooks at the rear side of backrest.




11. Remove the hog rings (A) in the side airbag module installation side.




12. Remove the cover frame (A).




13. Remove the headrest lock bushing.

NOTE: Push outside to remove it from the inside of seat.

14. Pull out the backrest frame assembly.




15. Remove the two bolts on each left and right side, and then remove the reclining motor assembly.




16. Remove the hog rings (A) on the front side of backrest, and then remove the backrest cover from backrest.




17. Remove the clip (A) and straps (B) on the back of seat cushion.




18. Remove the bolt (A) and hook (B) on left and right side, and then remove the seat cushion frame from seat rail assembly.




19. Remove the hooks (A), and then remove the seat cushion from seat cushion frame.




20. Remove the hog rings (A), and then remove the seat cushion cover from seat cushion pad.




21. Remove the hooks and hog rings at the bottom of headrest, and then remove the headrest cover from headrest.

ASSEMBLY

CAUTION: When the backrest cover is not installed securely, the side airbag module may not be deployed properly, therefore keep strictly to the following procedure.
- Be careful not to stain or damage the backrest cover during assembly.
- Always use new hog rings.
- Secure the hog ring using hog ring pliers.
- Install the hog rings to the specified points securely and make sure that no wrinkle or twisting on the backrest cover.

DRIVER'S SEAT
Assemble in the reverse order of disassembly.

NOTE:
- Install the inner seat belt in the procedure described in "Front Seat Belt".
- Install the backrest assembly and seat cushion assembly in the following procedure.

1. Temporarily tighten the four reclining hinge bolts.
2. Place the backrest in the most upright position. (For manual seat, ensure the reclining mechanism locked securely.)




3. Tighten the reclining hinge bolts (1) - (4) in two or three steps by gradually increasing the torque until they reach the specified torque.