Preparation For the Inspection Mode - Using a Scan Tool
PREPARATION FOR THE INSPECTION MODE1. Check battery voltage is more than 12 V and fuel remains half [20 to 40 2 (5.3 to 10.6 US gal, 4.4 to 8.8 Imp gal)].
2. Lift-up the vehicle using a garage jack and place it on rigid racks, or drive the vehicle onto free rollers.
WARNING:
- Before lifting-up the vehicle, ensure parking brakes are applied.
- Do not use a pantograph jack in place of a rigid rack.
- Secure a rope or wire to the front or rear towing hooks to prevent the lateral runout of front wheels.
- Do not abruptly depress/release clutch pedal or accelerator pedal during works even when the engine is operating at low speeds since this may cause vehicle to jump off free rollers.
- In order to prevent the vehicle from slipping due to vibration, do not place any wooden blocks or similar items between the rigid racks and vehicle.
- Since the rear wheels will also rotate, do not place anything near them. Also, make sure that nobody goes in front of the vehicle.
SUBARU SELECT MONITOR
1. After clearing the memory, check for any remaining unresolved trouble data. Clearing Trouble Codes
2. Idle the engine.
3. Prepare the Subaru Select Monitor kit.
4. Connect the diagnosis cable to Subaru Select Monitor.
5. Insert the cartridge to Subaru Select Monitor.
6. Connect the test mode connector (A) located under the glove box.
7. Connect the Subaru Select Monitor to the data link connector at the lower portion of instrument panel (on the driver's side).
CAUTION: Do not connect any scan tools except Subaru Select Monitor or general scan tool.
8. Turn the ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
9. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
10. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
11. Press the [YES] key after the information of engine type has been displayed.
12. On the "Engine Diagnosis" display screen, select the {D Check} and press the [YES] key.
13. When the "Perform D Check?" is shown on the screen, press the [YES] key.
14. Perform subsequent procedures as instructed on the display screen.
- If trouble still remains in the memory, the corresponding DTC appears on the display screen.
NOTE:
- For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
- For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". List of Diagnostic Trouble Code (DTC)
- Release the parking brake.
- The speed difference between front and rear wheels may light the ABS warning light, but this indicates no malfunctions. When engine control diagnosis is finished, perform the ABS memory clearance procedure of self-diagnosis function.
GENERAL SCAN TOOL
1. After performing the diagnostics and clearing the memory, check for any remaining unresolved trouble data. Clearing Trouble Codes
2. Idle the engine.
3. Connect the test mode connector (A) located under the glove box.
4. Connect the Subaru Select Monitor to the data link connector at the lower portion of instrument panel (on the driver's side).
CAUTION: Do not connect any scan tools except Subaru Select Monitor or general scan tool.
5. Start the engine.
NOTE: Make sure the select lever is placed in "P" position before starting.
6. Using the select lever, turn the "P" position switch and the "N" position switch to ON.
7. Depress the brake pedal to turn brake switch ON.
8. Keep the engine speed in 2,500 - 3,000 rpm range for 40 seconds.
9. Shift the select lever in the "D" range and drive the vehicle at 5 to 10 km/h (3 to 6 MPH).
NOTE:
- For AWD model, release the parking brake.
- The speed difference between front and rear wheels may light the ABS warning light, but this indicates no malfunctions. When engine control diagnosis is finished, perform the ABS memory clearance procedure of self-diagnosis system.
10. Using the general scan tool, check DTC and record the result(s).
NOTE:
- For detailed operation procedure, refer to the general scan tool operation manual.
- For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". List of Diagnostic Trouble Code (DTC)