Disassembly and Assembly

FRONT SEAT

DISASSEMBLY

CAUTION: Refer to CAUTION in before starting the work.

1. STANDARD SEAT
1. Remove the seat from vehicle.




2. Remove the seat lifter cover using a flat tip screwdriver or equivalent, and then loosen the inside bolt to remove seat lifter lever.




3. Remove the reclining lever and seat hinge outer cover.




4. Remove the seat hinge inner cover.




5. Remove the inner belt.




6. Remove two bolts from reclining hinge on each side.




7. Remove the hook at the bottom-back side of backrest.




8. Open the zipper behind of backrest.




9. Remove the hog rings (A) of backrest cover.




10. Remove the hog rings (A) which secure the backrest cover and backrest pad.




11. Open the zipper behind of backrest cover, and then remove the hog rings (A) at the side-inner part of backrest from backrest frame.




12. Remove the headrest bushings.

NOTE:Push the headrest bushings out from seat inside, and then remove them.

13. Pull out the backrest frame.




14. Remove the hog rings (A) at the front-bottom of seat back.




15. Remove the hog rings (A) at the seat back front, and then remove the seat back cover from seat back.




16. Remove the hooks (A), and then remove the seat cushion frame assembly.




17. Remove the hog rings (A), and then remove the seat cushion cover from seat cushion pad.




18. Remove the bolt of sliding adjustment bar and connecting wire.




19. Remove the bolts, and then remove the slide rail.




20. Open the zipper at bottom of headrest, and then remove the headrest cover from headrest.

2. BUCKET TYPE SEAT
1. Remove the seat from vehicle.




2. Remove the seat lifter cover using a flat tip screwdriver or equivalent, and then loosen inside bolt to remove seat lifter lever.




3. Remove the reclining lever and seat hinge outer cover.




4. Remove the seat hinge inner cover.




5. Remove the inner belt.




6. Remove two bolts from reclining hinge on each side.




7. Remove the hook at the bottom-back side of backrest.




8. Remove the hooks (A), and then remove the seat cushion frame assembly.




9. Remove the bolt of sliding adjustment bar and connecting wire.




10. Remove the bolts, and then remove the slide rail.

ASSEMBLY

1. STANDARD SEAT

CAUTION:
1. Because it may cause the side airbag to activate incorrectly, observe the following steps to install the side airbag correctly.
- Be careful not to contaminate or damage the backrest cover.
- Always use new hog rings.
- Secure the hog ring using hog ring pliers.
- Install the hog ring to its original position, and not to twist or wrinkle the backrest cover.

2. To avoid the improper operation of occupant detection system, strictly obey the following works at assembly of passenger s seat.
- If the seat cushion cover has been removed or replaced, be sure to perform the system calibration for occupant detection system after installing the seat.
- Failure to do so may cause improper operation of passenger s airbag.
- Never remove the occupant detection control module of occupant detection system (passenger's side only) and occupant detection sensor from seat cushion frame since the control module, the sensor, seat cushion pad and seat cushion frame are the seat cushion pad and frame assembly.
- Do not remove the seat position sensor from seat rail. (Driver's seat).
- The seat cushion cover has been removed, be sure to replace wire on the seat cushion cover side with a new one. (Passenger's seat)
- Install the hog ring to the specified position correctly. Do not re-use the hog ring.

Tightening torque: Nm (kgf-m, ft-lb)
T1: 5.9 (0.60, 4.35)
T2: 10 (1.02, 7.38)
T3: 22 (2.24, 16.2)
T4: 30 (3.06, 22.1)
T5: 52 (5.30, 38.4)
T6: 53 (5.40, 39.1)

Assemble in the reverse order of disassembly.

2. BUCKET TYPE SEAT
Assemble in the reverse order of disassembly.

Tightening torque: Nm (kgf-m, ft-lb)
T1: 5.9 (0.60, 4.35)
T2: 10 (1.02, 7.38)
T3: 22 (2.24, 16.2)
T4: 30 (3.06, 22.1)
T5: 52 (5.30, 38.4)
T6: 53 (5.40, 39.1)