Front Differential Assembly
Front Differential AssemblyREMOVAL
1) Remove the manual transmission assembly.
2) Prepare the transmission for overhaul.
3) Remove the oil pipe, neutral position switch, back-up light switch and harness.
4) Remove the extension case.
5) Remove the transfer driven gear.
6) Remove the center differential.
7) Remove the oil pump.
8) Remove the transmission case.
9) Remove each gear assembly.
10) Remove the drive pinion shaft assembly.
11) Remove the retainer lock plates on both side.
12) Using the ST, remove the differential side retainer on both side.
ST1 499787000 WRENCH ASSY (RIGHT SIDE)
ST2 18630AA000 WRENCH ASSY (LEFT SIDE)
NOTE:
Be careful not to damage the part of clutch case where the retainer is to be installed.
13) Remove the front differential.
INSTALLATION
1) Install the differential assembly into clutch housing.
2) Apply oil to the threaded portion part of differential side retainer.
3) Remove the O-ring from differential side retainer of both sides.
4) Using the ST, install the differential side retainer to both sides.
ST1 499787000 WRENCH ASSY (RIGHT SIDE)
ST2 18630AA000 WRENCH ASSY (LEFT SIDE)
NOTE:
Be careful not to damage the oil seal.
5) Check and adjust the hypoid gear backlash.
6) Check and adjust the tooth contact.
7) Mark an engagement point on the right and left side retainer and clutch housing.
8) Remove the differential side retainer from both sides.
NOTE:
Note the rotating number of time till removal, when removing the differential side retainer.
9) Install a new O-ring to differential side retainer of both sides.
10) Install the differential side retainer to both sides.
NOTE:
Install the differential side retainer by screwing in the same rotating number of time till removal, and then align the mark.
11) Install the retainer lock plate.
Tightening torque:
25 Nm (2.5 kgf-m, 18.1 ft. lbs.)
NOTE:
Be careful not to confuse right and left retainer lock plates.
12) Completely remove the remaining gasket from the clutch housing and adapter plate.
13) Apply liquid gasket to the clutch housing.
Liquid gasket:
THREE BOND 1215 (Part No. 004403007)
14) Install the drive pinion shaft assembly.
15) Install each gear assembly at once.
16) Install the transmission case.
17) Install the oil pump.
18) Install the center differential.
19) Install the transfer driven gear.
20) Install the extension case.
21) Install the oil pipe, neutral position switch, back-up light switch and harness.
22) Install the manual transmission assembly to vehicle.
DISASSEMBLY
DIFFERENTIAL CASE
1) Secure the differential assembly on a vise, and then remove the hypoid driven gear.
2) Using the ST, remove the hypoid driven gear side bearing.
ST 399527700 PULLER SET
3) Using a screw driver, make clearance of 2 - 3 mm (0.079 - 0.118 inch) between the speedometer drive gear and roller bearing.
NOTE:
Be careful not to damage the differential case.
4) Using the ST, remove the roller bearing.
ST 498077000 REMOVER
DIFFERENTIAL SIDE RETAINER
1) Remove the O-ring from differential side retainer.
2) Remove the oil seal from differential side retainer.
3) Remove the claw of ST1, and then install the claw of ST2.
ST1 398527700 PULLER ASSY
ST2 18760AA000 CLAW
4) Remove the bearing outer race from differential side retainer.
ST1 398527700 PULLER ASSY
ST2 18760AA000 CLAW
ASSEMBLY
DIFFERENTIAL CASE
1) Using the ST, install a new speedometer drive gear and right and left side bearing inner race to differential case. ST1 398437700 INSTALLER ST2 398497701 SEAT
CAUTION:
Do not apply pressure in excess of 20 kN (2.0 ton, 2.2 US ton, 2.0 Imp ton).
NOTE:
Always replace the inner race and outer race as a set.
2) Install the hypoid driven gear to differential case.
DIFFERENTIAL SIDE RETAINER
1) Using the ST, install the oil seal.
ST 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER
2) Install the bearing outer race to differential side retainer on both sides.
3) Install the O-ring to differential side retainer on both sides.
NOTE:
Be careful not to damage the O-ring.
INSPECTION
Repair or replace the front differential in following cases.
^ Each gear is damaged, seized, or excessively worn.
^ Sliding surface of the differential case is damaged, seized or excessively worn.
^ Bearings and bearings part are damaged, rusted or worn.
^ Bearings fail to turn smoothly or make abnormal noise when turned.
HYPOID GEAR BACKLASH
Check the hypoid gear backlash. If it is not within specifications, adjust it.
TOOTH CONTACT OF HYPOID GEAR
1) Be sure the hypoid gear backlash is within specifications. If it is not within specifications, adjust it.
2) Apply a uniform thin coat of red lead on both tooth surfaces of three or four teeth of the hypoid driven gear.
3) Install the drive pinion shaft assembly, and then secure it with five bolts.
NOTE:
Use the old gasket and washer to prevent the mating surface of housing from damaging.
Tightening torque:
50 Nm (5.1 kgf-m, 36.9 ft. lbs.)
4) Rotate the drive pinion shaft to right and left for several times.
5) Remove the drive pinion shaft assembly, and then check tooth contact. If tooth contact is inaccurate, adjust it.
^ Correct tooth contact.
NOTE:
Under no load, tooth contacts 50 - 60% from center to toe side (tooth contact shifts to heel side when driving).
ADJUSTMENT
HYPOID GEAR BACKLASH
1) Install the right and left side differential side retainer.
ST1 499787000 WRENCH ASSY (RIGHT SIDE)
ST2 18630AA000 WRENCH ASSY (LEFT SIDE)
NOTE:
Screw in the right side differential side retainer a bit further than left side.
2) Install the drive pinion shaft assembly, and then secure it with five bolts.
NOTE:
Use the old gasket and washer to prevent the mating surface of housing from damaging.
Tightening torque:
50 Nm (5.1 kgf-m, 36.9 ft. lbs.)
3) Using the ST, screw in the left side differential side retainer until the drive pinion and hypoid driven gear contacts lightly. Then loosen the right side differential side retainer.
ST1 499787000 WRENCH ASSY (RIGHT SIDE)
ST2 18630AA000 WRENCH ASSY (LEFT SIDE)
4) Using the ST, rotate the drive pinion shaft several times.
ST 18631AA000 HANDLE
5) Repeat step (3) and (4) until the left side differential side retainer can not be rotated. For the right side differential side retainer, screw it in until the inner race and outer race contacts lightly. This condition is "0" backlash.
6) Mark an engagement point on the right and left side retainer and clutch housing.
7) Return the left side differential side retainer for three teeth, and screw in the right side differential side retainer for three teeth.
8) Using the ST, secure the drive pinion shaft.
ST 18621AA000 ADAPTER WRENCH
9) Install the axle shafts to both sides of front differential.
Parts No. 38415AA000 AXLE SHAFT
10) Move the axle shaft, and measure the hypoid gear backlash.
ST1 498255400 PLATE
ST2 498247001 MAGNET BASE
ST3 498247100 DIAL GAUGE
11) If the backlash is out of specification, adjust it by turning the right and left side differential side retainers.
12) Screw in the right side differential side retainer for further 1.75 teeth.
TOOTH CONTACT OF HYPOID GEAR
Refer to the section of drive pinion shaft for checking of tooth contact.