Front Vehicle Speed Sensor
Front Vehicle Speed SensorREMOVAL
1) Set the vehicle on a lift.
2) Disconnect the ground cable from the battery.
3) Remove the air intake chamber. (Non-turbo model)
4) Remove the intercooler. (Turbo model)
5) Disconnect the transmission harness connector.
6) Remove the pitching stopper.
7) Remove the transmission harness connector from stay.
8) Lift up the vehicle.
9) Clean the transmission exterior.
10) Drain the ATF completely.
NOTE: Tighten the drain plug (ATF) after draining the ATF.
Tightening torque: 25 N-m (2.5 kgf-m, 18.4 ft-lb)
11) Remove the front, center and rear exhaust pipes and the muffler. (Non-turbo model)
12) Remove the center and rear exhaust pipes and the muffler. (Turbo model)
13) Remove the propeller shaft.
14) Place the transmission jack under the transmission.
NOTE: Make sure that the support plate of transmission jack does not touch the oil pan.
15) Remove the transmission rear crossmember bolt.
16) Lower the transmission jack.
NOTE: Do not separate the transmission jack and transmission.
17) Remove the ATF inlet and outlet pipes.
NOTE: When removing the outlet pipe, do not lose the ball and spring used with the retaining screw.
18) Remove the front vehicle speed sensor and torque converter turbine speed sensor.
19) Disconnect the connector from the rear vehicle speed sensor.
20) Remove the oil pan.
21) Disconnect the control valve connector and the grounding cable.
22) Remove the transmission harness assembly.
INSTALLATION
1) Pass the transmission harness assembly through the hole in transmission case.
2) Connect the control valve connector and the grounding cable.
Tightening torque: 8 N-m (0.8 kgf-m, 5.8 ft-lb)
3) Apply proper amount of liquid gasket to the entire oil pan mating surface.
Liquid gasket: THREE BOND 1217B (Part No. K0877YA020) or equivalent
4) Fill the 3 holes aside from the bolt holes in the transmission case, with liquid gasket.
Liquid gasket: THREE BOND 1217B (Part No. K0877YA020) or equivalent
5) Install the oil pan by equally tightening the bolts.
Tightening torque: 5 N-m (0.5 kgf-m, 3.7 ft-lb)
6) Install the front vehicle speed sensor and torque converter turbine speed sensor.
Tightening torque: 7 N-m (0.7 kgf-m, 5.1 ft-lb)
7) Connect the connector to the rear vehicle speed sensor.
8) Install the ATF inlet and outlet pipes.
NOTE: Use a new copper washer.
Tightening torque:
T1: 25 N-m (2.5 kgf-m, 18.4 ft-lb)
T2: 40 N-m (4.1 kgf-m, 29.5 ft-lb)
T3: 45 N-m (4.6 kgf-m, 33.2 ft-lb)
9) Install the transmission rear crossmember bolt.
Tightening torque: 70 N-m (7.1 kgf-m, 51.6 ft-lb)
10) Install the propeller shaft.
11) Install the front, center and rear exhaust pipes, and the muffler. (Non-turbo model)
12) Install the center, rear exhaust pipes and the muffler. (Turbo model)
13) Lower the vehicle.
14) Attach the transmission harness connector to the stay.
15) Install the pitching stopper.
16) Install the air intake chamber. (Non-turbo model)
17) Install the intercooler. (Turbo model)
18) Pour in ATF.
19) Bleed the air of control valve.
20) Check the level and leaks of the ATF.
21) Execute the learning control promotion.