Front Seat
FRONT SEATDISASSEMBLY
1. STANDARD SEAT
1. Remove the seat from vehicle.
2. Remove the seat lifter cover using a flat tip screwdriver and loosen the inner bolt to remove the seat lifter lever.
3. While pulling the reclining lever, disengage the claw (A) on the back to remove the reclining lever cover.
4. Remove screws (A) and clips (B), and then detach the seat side cover outside.
5. Remove the TORX bolt, and then remove the inner seat belt assembly.
6. Loosen the screws to detach the seat side cover inside.
7. Remove the bolts from the left and right reclining hinges.
8. Remove the plastic fastener at the bottom-back side of backrest.
9. Open the fastener at the rear side of backrest.
10. Remove the hog rings of backrest cover.
CAUTION: When removing the hog rings, be careful not to tear the vinyl sheet within the seat. If the sheet has torn, replace it with a new sheet.
11. Remove the pad (A) and then remove the mounting nuts for side airbag module.
12. Remove the headrest bushing.
NOTE: Push outside to remove it from the inside of seat.
13. Pull out the backrest frame.
14. Remove all the hog rings at front of seat back, and then remove the seat back cover from seat backrest.
15. Remove the plastic hooks (A) of the seat cushion cover, and then remove the seat cushion frame assembly.
16. Remove all the hog rings, and then remove the seat cushion cover from seat cushion pad.
17. Remove the bolts on the side of seat cushion assembly, then remove the slide rail.
18. Open the plastic fastener on the bottom of the headrest, then remove the headrest cover from the headrest.
2. PASSENGER'S SEAT
CAUTION:
- If the seat cushion cover is removed or replaced, make sure to perform passenger detection system adjustment after installing the seat to the vehicle.
- The passenger detection system (passenger seat only) control unit, passenger detection sensor, seat cushion pad and seat cushion frame are considered as a single seat cushion pad and frame assembly. Never remove the passenger detection control unit or the pressure sensor from the seat cushion frame.
- If the seat cushion cover is removed, make sure to replace the hang wire on the seat cushion side with a new wire.
1. Remove the seat from vehicle.
2. Refer to the disassembly procedures for the driver's seat.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION: When installing the side airbag module assembly, be sure to install it by inserting the side airbag module between the backrest cover and airbag guide cloth.
When the backrest cover is not installed securely, the side airbag module may not be deployed properly, therefore keep strictly to the following procedure.
- Be careful not to stain or damage the backrest cover during assembly.
- Always use new hog rings.
- Secure the hog ring using hog ring pliers.
- Install the hog rings to the specified points
securely and make sure that no wrinkle or twisting on backrest cover.
Tightening torque: Refer to "COMPONENT" of "General Description".
1. DRIVER'S SEAT
NOTE:
- When installing the inner seat belt assembly, follow the procedure described in the seat belt section.
- Install the backrest assembly and seat cushion assembly in the following procedure.
1. Temporarily tighten the four reclining hinge bolts.
2. Place the backrest in the most upright position.
3. Tighten the reclining hinge bolts in the order of (1) through (4), in two or three steps by gradually increasing the torque until they reach the specified torque.
4. Assemble in the reverse order of disassembly.
2. PASSENGER'S SEAT
CAUTION: Make sure to adhere to the following rules when assembling the passenger seat. Improper work procedures can cause the passenger detection system to not operate properly.
- If the seat cushion cover is removed or replaced, make sure to perform passenger detection system adjustment after installing the seat to the vehicle.
- The passenger detection system (passenger seat only) control unit, passenger detection sensor, seat cushion pad and seat cushion frame are considered as a single seat cushion pad and frame assembly. Never remove the passenger detection control unit or the pressure sensor from the seat cushion frame.
- If the seat cushion cover is removed, make sure to replace the hang wire on the seat cushion side with a new wire.
- Make sure to install the hog rings/clips to the specified locations. Do not reuse hog rings.
Assemble in the reverse order of disassembly.
1. Assemble the seat cushion in the reverse order of disassembly.
2. Assemble the backrest in the reverse order of disassembly.
3. When installing the backrest assembly to the seat cushion assembly, fill the gap in the front side of slide rail LH and in the rear side of slide rail RH with cloth etc. in order to stabilize the seat cushion assembly.
4. Temporarily tighten the reclining hinge bolts in the order of (1) through (4) to an extent that the seat backrest assembly is not held securely.
5. Use the reclining lever to place the backrest in the most upright position, and check the first lock position of recliner.
6. Hold the seat cushion assembly securely, and tighten the reclining hinge bolts in the order described above until they reach the specified torque.
CAUTION: Do not touch the backrest assembly when tightening the reclining hinge bolts.
7. Assemble each harness, inner belt assembly and each cover in the reverse order of removal.
Tightening torque: Refer to "COMPONENT" of "General Description".
INSPECTION
Check that no tear or fray on the backrest cover and seat cushion cover.
NOTE: If the door side of the backrest cover is torn or frayed, the side airbag may not be deployed properly. In this case, replace the backrest cover.