Oil Pump: Service and Repair

Oil Pump





REMOVAL
1) Set the vehicle on a lift.
2) Remove the collector cover.
3) Disconnect the ground cable from the battery.





4) Lift up the vehicle.
5) Remove the under cover.
6) Remove the bolts which install water pipe of oil cooler to oil pump.





7) Remove the water pipe and hoses between oil cooler and water pump.





8) Lower the vehicle.
9) Remove the radiator.
10) Remove the crankshaft position sensor.
11) Remove the V-belts.
12) Remove the belt tensioner.





13) Remove the crank pulley using ST.





14) Remove the water pump.
15) Remove the timing belt guide. (MT model)





16) Remove the crank sprocket.





17) Remove the bolts which install oil pump onto cylinder block.

NOTE: When disassembling and checking the oil pump, loosen the relief valve plug before removing the oil pump.





18) Remove the oil pump by using flat tip screwdriver.

CAUTION: Be careful not to scratch mating surfaces of cylinder block and oil pump.





19) Remove the front oil seal from the oil pump.

INSTALLATION
Install in the reverse order of removal.
Perform the following.

1) Using the ST, install the front oil seal.
ST 499587100 OIL SEAL INSTALLER

NOTE: Use a new front oil seal.





2) Apply liquid gasket to the mating surfaces of oil pump.

NOTE: Install within 5 min. after applying liquid gasket.

Liquid gasket: THREE BOND 1217G (Part No. K0877Y0100) or equivalent





3) Apply a coat of engine oil to the inside of oil seal.





4) Install the oil pump to cylinder block. Be careful not to damage the oil seal during installation.

NOTE:
^ Make sure the front oil seal lip is not folded.
^ Align the flat surface of oil pump's inner rotor with crankshaft before installation.
^ Use new O-rings.

5) Apply liquid gasket to the three bolts thread shown in figure. (when reuse the bolts)
Liquid gasket: THREE BOND 1324 (Part No. 004403042) or equivalent





DISASSEMBLY
Remove the screw which secures oil pump cover and then disassemble oil pump. Inscribe alignment marks on the inner and outer rotors so that they can be replaced in their original positions during reassembly.

NOTE: Before disassembling the oil pump, remove the relief valve.





ASSEMBLY
1) Using the ST, install the front oil seal.
ST 499587100 OIL SEAL INSTALLER

NOTE: Use a new front oil seal.





2) Apply a coat of engine oil to inner and outer rotors.
3) Assemble the inner and outer rotors in their original positions.
4) Assemble the oil relief valve and install relief valve spring and plug.

NOTE: Use a new gasket.

5) Install the oil pump cover.





INSPECTION

TIP CLEARANCE
Measure the tip clearance of rotors. If the clearance is out of specification, replace the rotors as a set.





CASE CLEARANCE
Measure the clearance between the outer rotor and the oil pump case. If clearance is out of standard, replace the oil pump case.





SIDE CLEARANCE
Measure the clearance between the inner rotor and the oil pump cover by checking the step between the inner rotor and the oil pump cover as shown in the following figure. If the clearance is out of specification, replace the rotors and the oil pump case.





OIL RELIEF VALVE
Check the valve for assembly condition and damage, and the relief valve spring for damage and deterioration. Replace the parts if defective.
Relief valve spring:
Free length: 73.7 mm (2.902 in)
Installed length: 54.7 mm (2.154 in)
Load when installed: 93.1 N (9.49 kgf, 20.88 lbf)

OIL PUMP CASE
Check the oil pump case for worn shaft hole, clogged oil passage, worn rotor chamber, cracks and other faults.

OIL SEAL
Check the oil seal lips for deformation, hardening, wear, etc. and replace if defective.