Subaru Select Monitor
Subaru Select MonitorOPERATION
1. READ DIAGNOSTIC TROUBLE CODE (DTC)
NOTE:
- DTC is displayed in the sequence of inputting. (When entering two DTCs or more simultaneously, they are displayed in the sequence of priority.)
- When more than two DTCs are displayed, perform the diagnosis of top one.
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Connect the Subaru Select Monitor to data link connector. Data link connector is located in the lower portion of instrument panel (on the driver's side).
CAUTION: Do not connect the scan tools except for Subaru Select Monitor.
4. Turn the ignition switch to ON (engine OFF) and run the Subaru Select Monitor.
5. On the <
6. On the <
7. On the <
NOTE:
- It is possible to read the DTC at the {Check all diagnosis codes} on the <
- For details concerning the operation procedure, refer to the "PC application for Subaru Select Monitor".
- For details concerning DTCs, refer to the List of Diagnostic Trouble Code (DTC). DTC List - B and U Codes
2. READ CURRENT DATA
1. On the <
2. On the <
3. On the <
4. Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A support list contains both of analog and digital data, and they are shown in the following table.
3. DISPLAY OF ANALOG DATA
4. DISPLAY OF ON/OFF DATA
NOTE: For details concerning operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
5. CONFIRMATION OF CURRENT SETTING
1. On the <
2. On the <
3. On the <
4. On the <
5. Using the scroll key, scroll the display screen up or down until the desired data is shown.
6. Display the following item and record the settings. Required items for new registration (Except for system not equipped)
6. REGISTRATION BODY INTEGRATED UNIT (EQUIPMENT SETTING)
CAUTION:
Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.
If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.
- Be sure to correspond registrations and function settings to vehicle equipment.
- Do not change the settings of vehicle improperly.
- Confirm key illumination does not blink or "Factory initial setting" of body integrated unit registrations is "Market". If "Factory initial setting" is set to "Factory," key illumination blinks with ignition key turned to ON to give warning of unconfirmed settings.
- Key illumination does not blink with ignition switch turned to ON and go off with door closed.
- Be sure to register immobilizer if body integrated unit is replaced with a new part. (Model with immobilizer)
- Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the "REGISTRATION MANUAL FOR IMMOBILIZER".
- Do not install or register an immobilizer related module of other registered vehicles in order to diagnose failures or inspect functions.
1. Turn the ignition switch to OFF.
2. Connect the Subaru Select Monitor to data link connector.
3. Turn the ignition switch to ON and run the Subaru Select Monitor.
4. On the <
5. On the <
6. Change the setting with UP/DOWN key and select the [OK]. Also, it is possible to set by changing to factory mode and pressing the wiper deicer switch, rear defogger switch, rear fog light switch and door lock switch.
NOTE:
Center display yes/no can be set only by the select monitor.
- List of body integrated unit registration item
- Setting is different depending on grade of vehicle and what is equipped.
CAUTION:
- It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.
- When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed.
- Be sure not to change Factory initial setting except installation of new body integrated unit.
NOTE:
"Factory" mode:
- Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
- All body integrated units as spare parts are set to "Factory" mode. When replacing a body integrated unit, be sure to perform the registration operation.
"Market" mode: Each settings have been set. It can be recognized by key illumination coming on in concocting with room light and going off with ignition switch turned to ON.
7. Perform the Factory setting. On the <
9. Register the immobilizer key.
10. Perform the registration according to the procedures of the "IMMOBILIZER REGISTRATION OPERATION MANUAL".
11. When the key registration is completed, perform the function setting (Module customization).
7. CLEAR MEMORY MODE
1. On the <
2. On the <
3. Select the [OK] after the information of body integrated unit type is displayed.
4. On the <
5. When "Done" is shown on the display screen, turn the ignition switch to OFF.
NOTE: For details concerning the operation procedure, refer to the "PC application for Subaru Select Monitor".
8. FREEZE FRAME DATA
NOTE:
- Data stored at the time of trouble occurrence is shown on display.
- Freeze frame data will be memorized maximum to 20.
- If freeze frame data is not stored in memory correctly (caused by low power supply of body integrated unit), DTC will be displayed with "?" on the head of it in the Subaru Select Monitor display. This shows it may be an unreliable reading.
9. FUNCTION SETTING (ECM CUSTOMIZING)
1. On the <
2. On the <
3. On the <
4. Change the setting.
- List of function setting item (ECM customizing)
NOTE: Even if changes are made to items that are not equipped, the contents are not confirmed and do not operate.
5. After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Display & Save}.
CAUTION:
- It is possible to control the original functions of vehicle when settings above are corresponded to vehicle equipment.
- Do not change the settings except for setting above during operation of equipment setting.
- Be sure not to change Factory initial setting except installation of new body integrated unit.
NOTE: For details concerning the operation procedure, refer to the "PC application for Subaru Select Monitor".
10. FUNCTION CHECK
In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.
1. On the <
2. On the <
3. On the <
4. Select the item to be operated on the <
5. Pressing [OK] starts, [NO] cancels the operation and [OK] returns to the System Operation Check Mode display screen.
NOTE: If not equipped (based on area or condition), process will not go on.