Preparation For the Inspection Mode
PREPARATION FOR THE INSPECTION MODE1. Check that the battery voltage is 12 V or more and fuel remains approx. half [20 - 40 l (5.3 - 10.6 US gal, 4.4 - 8.8 Imp gal)].
2. Lift up the vehicle using a garage jack and place it on rigid racks, or drive the vehicle onto free rollers.
WARNING:
- Before raising the vehicle, ensure parking brakes are applied.
- Do not use a pantograph lack in place of a rigid rack.
- Secure a rope or wire to the front or rear towing hooks to prevent the lateral runout of front wheels.
- Before rotating the wheels, make sure that there is no one in front of the vehicle. Besides while the wheels are rotating, make sure that no one approaches the vehicle front side.
- Make sure that there is nothing around the wheels. For AWD model, pay special attention to all four wheels.
- While servicing, do not depress or release the clutch pedal or accelerator pedal quickly regardless of the engine speed. Quick operation may cause the vehicle to drop off the free roller.
- To prevent the vehicle from slipping due to vibration, do not place anything between rigid rack and the vehicle.
SUBARU SELECT MONITOR
1. After clearing the memory, check for any remaining unresolved trouble data.
2. Warm up the engine.
3. Prepare the Subaru Select Monitor kit.
4. Prepare the personal computer which has been installed the Subaru Select Monitor.
5. Connect the USB cable between SDI (Subaru Diagnosis Interface) and USB port on the personal computer (dedicated port for the Subaru Select Monitor).
NOTE: The dedicated port for the Subaru Select Monitor means the USB port which was used to install the Subaru Select Monitor.
6. Connect the diagnosis cable to the SDI.
7. Connect the delivery (test) mode connector (A) located under the glove box.
8. Connect the SDI to data link connector located in the lower portion of the instrument panel (on the driver's side).
CAUTION: Do not connect any scan tools except Subaru Select Monitor and general scan tool.
9. Start up the personal computer.
10. Turn the ignition switch to ON (engine OFF), and run the "PC application for Subaru Select Monitor".
11. On the [[Main Menu]] display screen, select the {Each System Check}.
12. On the [[System Selection Menu]] display screen, select the {Engine Control System}.
13. Click the [OK] button after the information of engine type has been displayed.
14. On the [[Engine Diagnosis]] display screen, select the {Dealer Check Mode Procedure}.
15. When the [[Perform Inspection (Dealer Check) Mode]] is shown on the screen, click the [Next] button.
16. Perform subsequent procedures as instructed on the display screen.
- If trouble still remains in the memory, the corresponding DTC appears on the display screen.
NOTE:
- For detailed operation procedure, refer to the "PC application help for Subaru Select Monitor".
- For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". List of Diagnostic Trouble Code (DTC)
- Release the parking brake.
- The speed difference between front and rear wheels may illuminate the ABS warning light, but this does not indicate a malfunction. When engine control diagnosis is finished, perform the ABS memory clearance procedure of the self-diagnosis system.
GENERAL SCAN TOOL
1. After clearing the memory, check for any remaining unresolved trouble data.
2. Warm up the engine.
3. Connect the delivery (test) mode connector (A) located under the glove box.
4. Connect the general scan tool to data link connector located in the lower portion of the instrument panel (on the driver's side).
CAUTION: Do not connect any scan tools except Subaru Select Monitor and general scan tool.
5. Start the engine.
NOTE: Ensure the selector lever is placed in "P" range before starting.
6. Turn the neutral position switch to ON using select lever.
7. Depress the brake pedal to turn the brake switch ON.
8. Keep the engine speed in 2,500 - 3,000 rpm range for 40 seconds.
9. Place the select lever in "D" position and drive the vehicle at 5 to 10 km/h (3 to 6 MPH).
NOTE:
- For AWD model, release the parking brake.
- The speed difference between front and rear wheels may illuminate the ABS warning light, but this indicates no malfunctions. When engine control diagnosis is finished, perform the ABS memory clearance procedure of self-diagnosis system.
10. Using the general scan tool, check DTC and record the result(s).
NOTE:
- For detailed operation procedures, refer to the general scan tool operation manual.
- For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". List of Diagnostic Trouble Code (DTC)