Front Differential Assembly
Front Differential AssemblyREMOVAL
1) Remove the transmission assembly from the vehicle.
2) Pull out the torque converter clutch assembly.
3) Remove the input shaft.
4) Lift up the lever on the rear side of transmission harness connector, and then remove it from the stay.
5) Remove the inhibitor switch connector from the stay.
6) Remove the oil charge pipe.
7) Remove the ATF cooler inlet pipe and outlet pipe.
8) Separate the converter case from the transmission case.
9) Remove the seal pipe.
10) Remove the differential side retainers using ST.
NOTE:
^ ST WRENCH ASSY (499787000) can also be used.
^ Hold the differential case assembly by hand to avoid damaging the retainer mounting hole of the converter case.
ST 18630AA010 WRENCH COMPL RETAINER
11) Remove the front differential assembly while being careful not to damage the attachment part of the retainer.
INSTALLATION
1) Install the front differential assembly to the converter case.
NOTE:
Be careful not to damage the inside of the converter case (especially the mating surface of the differential side retainer).
2) Install the O-rings to the left and right side differential retainers.
NOTE:
Use new O-rings.
3) Install the differential side retainers using ST.
NOTE:
ST WRENCH ASSY (499787000) can also be used.
ST 18630AA010 WRENCH COMPL RETAINER
4) Adjust the backlash of the front differential.
5) Install the lock plate.
Tightening torque:
25 Nm (2.5 kgf-m, 18.4 ft-lb)
6) Install the seal pipe to the converter case.
NOTE:
Use a new seal pipe.
7) Install the converter case to the transmission case.
8) Insert the inhibitor switch connector and transmission harness connector onto the stay.
9) Install the ATF cooler pipe.
10) Install the oil charge pipe together with an Oring.
11) Apply ATF to the O-ring, insert the input shaft while rotating the shaft slowly by hand, and check the amount of protrusion.
NOTE:
Use new O-rings.
Normal protrusion A:
50 - 55 mm (1.97 - 2.17 in)
12) Install the torque converter clutch assembly.
13) Install the transmission assembly to the vehicle.
DISASSEMBLY
DIFFERENTIAL CASE ASSEMBLY
1) Remove the taper roller bearing using the ST and a press.
ST 498077000 REMOVER
2) Secure the case in a vise, remove the hypoid driven gear tightening bolts, and then separate the hypoid driven gear into differential case (RH) and differential case (LH).
3) Pull out the straight pin and pinion shaft, then remove the differential bevel gear, washer and differential bevel pinion.
SIDE RETAINER
NOTE:
After adjusting the drive pinion backlash and tooth contact, remove and install the oil seal and O-ring.
1) Remove the O-ring.
2) Remove the oil seal.
3) Remove the split pin, and then remove the claw.
ST 398527700 PULLER ASSY
4) Attach two claws to the outer race, and set the ST to the differential side retainer.
ST 398527700 PULLER ASSY
5) Restore the removed claws to original position, and install the pin and split pin.
6) Hold the shaft of ST to avoid detachment from the differential side retainer, and remove the bearing outer race.
NOTE:
Replace the bearing inner and outer races as a single unit.
ST 398527700 PULLER ASSY
ASSEMBLY
DIFFERENTIAL CASE ASSEMBLY
1) Install the washer, differential bevel gear and differential bevel pinion in the differential case (RH). Insert the pinion shaft.
2) Attach the straight pin in the reverse direction.
3) Install the washer and differential bevel gear to the differential case (LH). Put the differential case (LH) on the differential case (RH), and assemble the two cases.
4) Install the hypoid driven gear and secure by tightening the bolt.
Tightening torque:
62 Nm (6.3 kgf-m, 45.7 ft-lb)
5) Measurement of backlash (Selection of washer)
(1) Install the SUBARU genuine axle shaft to differential case.
Part No. 38415AA070 AXLE SHAFT
(2) Measure the gear backlash using ST1 and ST2, and then insert the ST2 though the access window of case.
NOTE:
^ Measure the backlash by applying a differential bevel pinion tooth between two differential bevel gear teeth.
^ When measuring, fix the differential bevel pinion gear in place with a screwdriver covered with cloth, or a similar tool.
Standard:
0.13 - 0.18 mm (0.0051 - 0.0071 in)
ST1 498247001 MAGNET BASE
ST2 498247100 DIAL GAUGE
(3) If the backlash is not within specification, select a washer from the table below.
6) Using the ST, install the taper roller bearing.
ST 398487700 INSTALLER
SIDE RETAINER
1) Install the bearing outer race to the differential side retainer.
2) Using the ST, install the differential side retainer oil seal by lightly tapping with a plastic hammer.
CAUTION:
Apply differential gear oil to the oil seal lips, and install the oil seal while being careful not to deform the lip.
NOTE:
Use a new oil seal.
ST 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER
3) Apply gear oil to the O-ring and install.
NOTE:
^ Use new O-rings.
^ Apply gear oil to O-ring.
INSPECTION
^ Check each component for scratches, damage or other faults.
^ Measure the backlash, and then adjust it to be within specification.
ADJUSTMENT
1) Using the ST, screw-in the differential side retainer until resistance is felt.
NOTE:
^ Screw-in the RH side slightly deeper than the LH side.
^ ST WRENCH ASSY (499787000) can also be used.
ST 18630AA010 WRENCH COMPL RETAINER
2) Remove the oil pump housing.
3) Remove the liquid gasket from the mating surface completely.
4) Install the oil pump housing assembly to the converter case, and secure them by tightening the four bolts evenly.
NOTE:
Use an old gasket or aluminum washer to prevent damaging the mating surface of the housing.
Tightening torque:
41 Nm (4.2 kgf-m, 30.2 ft-lb)
5) Rotate the drive pinion a few times using ST1 and ST2.
ST1 498937110 HOLDER
ST2 499787700 WRENCH
6) Tighten the LH differential side retainer by rotating the shaft until resistance is felt. Then loosen the RH side differential side retainer. Tighten the LH differential side retainer until the pinion shaft no longer turns, and continue to loosen the RH side. This is the "zero" state.
7) After reaching the "zero" state, loosen the LH differential side retainer by 3 notches and secure it with the lock plate. Then after returning the RH differential side retainer, retighten until it stops. Rotate the drive pinion 2 or 3 times. Tighten the RH differential side retainer further by 1-3/4 notches. This sets the preload. Finally, secure the differential side retainer with the lock plate.
NOTE:
Turning the differential side retainer by one notch changes the backlash approx. 0.05 mm (0.0020 in).
8) Install the SUBARU genuine axle shaft to the left and right sides of the front differential.
Part No. 38415AA000 AXLE SHAFT
9) Turn the drive pinion a few times with ST1 and check to see if the backlash is within the specified value, using ST2, ST3, ST4 and ST5.
ST1 499787700 WRENCH
ST2 498247001 MAGNET BASE
ST3 498247100 DIAL GAUGE
ST4 499787500 ADAPTER
ST5 498255400 PLATE
Backlash:
0.13 - 0.18 mm (0.0051 - 0.0071 in)
10) Adjust the teeth contact of the front differential and drive pinion shaft.