Operation CHARM: Car repair manuals for everyone.
Home >> Subaru >> 2012 >> Tribeca F6-3.6L DOHC >> Repair and Diagnosis >> Powertrain Management >> Computers and Control Systems >> Information Bus >> Testing and Inspection >> Scan Tool Testing and Procedures >> Subaru Select Monitor

Subaru Select Monitor

Subaru Select Monitor

OPERATION

1. READ DIAGNOSTIC TROUBLE CODE (DTC)

NOTE:
- DTC is displayed in the sequence of inputting. (When entering two DTCs or more simultaneously, they are displayed in the sequence of priority.)
- When more than one DTC is displayed, perform the diagnosis of top one.

1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Connect the Subaru Select Monitor to data link connector.
Data link connector is located in the lower portion of instrument panel (on the driver's side).






CAUTION: Do not connect scan tools other than the Subaru Select Monitor.

4. Turn the ignition switch to ON and run the Subaru Select Monitor.
5. On <
> display, select {Each System Check}.
6. On <> display, select {Integ. unit mode}.
7. On <> display, select {Diagnostic Code(s) Display}.

NOTE: It is possible to read the DTC at the {Check all diagnosis codes} on the <
>, and then find the contents to check from the DTC table. LAN System (Diagnostics)

NOTE:
- For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".
- For details concerning DTCs, refer to the List of Diagnostic Trouble Code (DTC). LAN System (Diagnostics)

2. READ CURRENT DATA
1. Select {Each System Check} in <
> display screen.
2. On the <> display screen, select the {Integ. unit mode}.
3. On the <> display screen, select the {Current Data Display & Save}.
4. Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A support list contains both of analog and digital data, and they are shown in the following table.

3. DISPLAY OF CURRENT DATA


















NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".

4. CONFIRMATION OF CURRENT SETTING
1. On <
> display, select {Each System Check}.
2. On <> display, select {Integ. unit mode}.
3. On <> display, select {Current Data Display & Save}.
4. On the <> display screen, select the {Data Display}.
5. Using the scroll key, scroll the display screen up or down until the desired data is shown.
6. Display the following item and record the settings.
Required items for new registration (Except for system not equipped)









5. REGISTRATION BODY INTEGRATED UNIT (EQUIPMENT SETTING)

CAUTION: Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.
If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.

- Be sure to correspond registrations and function settings to vehicle equipment.
- Do not change the settings of vehicle improperly.
- Confirm key illumination does not blink or "Factory or Market setting" of body integrated unit registrations is "Market". If "Factory initial setting" is set to "Factory," key illumination blinks when ignition key is ON, to notify that the settings are unconfirmed.
- Key illumination does not blink with ignition switch turned to ON and go off with door closed.
- Be sure to register immobilizer if body integrated unit is replaced with a new part. (models with immobilizer)
- Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the "PC application help for Subaru Select Monitor".
- Do not install or register an immobilizer related module of other registered vehicles in order to diagnose failures or inspect functions.

1. Turn the ignition switch to OFF.
2. Connect the Subaru Select Monitor to data link connector.






3. Turn the ignition switch to ON and run the Subaru Select Monitor.
4. On <
> display, select {Each System Check}.
5. On <> display, select {Integ. unit mode} and then select the <>.
6. Change the setting with UP/DOWN key and select the [OK].
Also, it is possible to set by changing to factory mode and pressing the wiper deicer switch, rear defogger switch, rear fog light switch and door lock switch.
- List of body integrated unit registration item

NOTE: Setting is different depending on the grade and equipment of the vehicle.






CAUTION:
- To perform normal operation of vehicle and diagnosis, above settings must match the actual vehicle equipment.
- When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed.
- Be sure not to change Factory or Market setting except when installing a new body integrated unit.

NOTE:
"Factory" mode:
- Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
- All replacement body integrated units are set to "Factory" mode. When replacing a body integrated unit, be sure to perform the registration operation.

"Market" mode:
Each settings have been set. It can be recognized by key illumination coming on in concocting with room light and going off with ignition switch turned to ON.

7. Perform the Factory or Market setting. On the <> display screen of Subaru Select Monitor, select the {Factory or Market setting}.
8. Change the mode from Factory to Market.
9. Register the immobilizer key.
10. Perform procedures according to the "PC application help for Subaru Select Monitor".
11. After registering the key, perform feature settings (unit customization).

6. CLEAR MEMORY MODE
1. On <
> display, select {Each System Check}.
2. On <> display, select {Integ. unit mode}.
3. Select the [OK] after the information of body integrated unit type is displayed.
4. On <> display, select {Clear Memory}.






5. When "Done" is shown on the display screen, turn the ignition switch to OFF.

NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".

7. FUNCTION SETTING (ECM CUSTOMIZING)
1. On <
> display, select {Each System Check}.
2. On <> display, select {Integ. unit mode}.
3. On <> display, select {Unit Customizing}.
4. Change the setting.
- List of function setting item (ECM customizing)

NOTE: Even if items that are not equipped are changed, contents of the change will not be confirmed, and will not operate.












5. After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Display & Save}.

CAUTION:
- The above settings must match the actual vehicle equipment for proper operation.
- Do not change settings except for setting above while setting the functions.
- Be sure not to change Factory or Market setting except when installing a new body integrated unit.

NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".

8. FUNCTION CHECK
In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.
1. On <
> display, select {Each System Check}.
2. On <> display, select {Integ. unit mode}.
3. On <> display, select {Function check}.
4. Select the item to be operated on the <> display screen and select the [OK].
5. Pressing [OK] starts, [NO] cancels the operation and [OK] returns to the System Operation Check Mode display screen.

NOTE: If not equipped (based on area or condition), process will not go on.

INSPECTION

1. COMMUNICATION FOR INITIALIZING IMPOSSIBLE

DETECTING CONDITION:
Defective harness connector

TROUBLE SYMPTOM:
Not communicable with Subaru Select Monitor.

WIRING DIAGRAM:
















CAUTION: When replacing body integrated unit on the model with immobilizer system, refer to the "PC application help for Subaru Select Monitor".
pro multis · About Operation CHARM