Assembly
Front Seat AssyASSEMBLY
NOTE: The procedures described below are for the LH side. Perform the same procedures for the RH side.
1. Installation of the seat track cover OUT LH
1. Engage 2 claws and install the seat track cover OUT LH.
NOTE: Install the both brackets by following the same procedures.
2. Installation of the front seat cushion protector No.1
1. Engage 2 claws and install the front seat cushion protector No.1.
NOTE: Install the both brackets by following the same procedures.
3. Installation of the reclining adjuster release band
1. Remove the screw and install the reclining adjuster release band.
4. Installation of the seat track adjusting handle
1. Install the seat track adjusting handle to the separate type front seat cushion frame ASSY RH.
CAUTION:
- Install the rear end of the seat track adjusting handle to the upper side of the seat track lever.
- Securely install 2 springs to the groove of the seat track adjusting handle.
5. Installation of the front seat cushion edge protector RH
1. Engage 3 claws and install the front seat cushion edge protector RH of the RH seat.
2. Install the screws.
6. Installation of the front seat cushion edge protector LH
NOTE: Install it in the same manner as the RH side.
7. Installation of the front seat cushion shield LWR RH (driver's side)
1. Temporally install the front seat cushion shield LWR RH with the clip.
2. Engage the hook.
3. Install the front seat cushion shield LWR RH with the screw.
8. Installation of the front seat cushion shield LWR LH (driver's side)
NOTE: Install it in the same manner as the RH side.
9. Installation of the separate type front seat cushion cover LH
1. Using hog ring pliers and 12 new hog rings, install the separate type front seat cushion cover LH to the separate type front seat cushion pad LH.
CAUTION:
- Be careful not to contaminate or damage the separate type front seat cushion cover LH.
- Align the centers of the fabric and the separate type front seat cushion pad LH taking care not to make wrinkles, and attach the hog rings.
NOTE: If the separate type front seat cushion cover LH for replacement is not provided with the retracting wire, reuse the original wire.
2. Using hog ring pliers, attach 2 new hog rings.
CAUTION: Be careful not to contaminate or damage the separate type front seat cushion cover LH.
10. Installation of the separate type front seat cushion cover with pad
1. Engage the hooks, and install the separate type front seat cushion cover with pad to the separate type front seat cushion frame ASSY LH.
2. Engage the claw and 3 clamps, and connect the wiring harness of the seat heater. (For the model with the seat heater)
3. Engage the claw, and connect the connector of the occupant detection sensor. (passenger's side)
11. Installation of the separate type front seat backrest cover LH
CAUTION:
- If the separate type front seat backrest cover LH is torn or frayed, the side airbag module LH may not be activated properly. In this case, replace the separate type front seat backrest cover LH with a new one.
- If the separate type front seat backrest cover LH is not installed securely, the side airbag module LH may not be activated properly. Therefore, keep strictly to the following procedures.
1. Using hog ring pliers and 14 new hog rings, install the separate type front seat backrest cover LH to the separate type front seat backrest pad LH.
CAUTION:
- Be careful not to contaminate or damage the separate type front seat backrest cover LH.
- Align the centers of the fabric and the separate type front seat backrest pad LH taking care not to make wrinkles, and attach the hog rings.
NOTE: If the separate type front seat backrest cover LH for replacement is not provided with the retracting wire, reuse the original wire.
12. Installation of the side airbag module LH
13. Installation of the separate type front seat backrest cover with pad
1. Install the separate type front seat backrest cover with pad to the separate type front seat backrest frame ASSY LH.
2. Install 3 brackets of the separate type front seat backrest cover LH with the nut.
Standard value: T = 5.5 N.m {56 kgf.cm} {4.1 ft.lbf}
WARNING:
- When installing the brackets, check that the band is not twisted.
- Wrap the side airbag module LH with the band, then install the brackets.
- If the brackets are not installed securely, the side airbag module LH may not be activated properly.
3. Engage 4 claws and install 2 front seat headrest supports.
4. Engage 2 hooks.
5. Close 2 fasteners.
6. Using hog ring pliers, attach 5 new hog rings.
CAUTION: Be careful not to contaminate or damage the separate type front seat backrest cover LH.
NOTE: If the separate type front seat backrest cover LH for replacement is not provided with the retracting wire, reuse the original wire.
14. Installation of the front seat backrest ASSY LH
1. Using the torque socket wrench (T40) and 4 new bolts, install the front seat backrest ASSY LH to the front seat cushion ASSY LH.
Standard value: T = 42 N.m {428 kgf.cm} {31.0 ft.lbf}
2. Engage the claw and 4 clamps, and connect the wiring harness of the side airbag module.
3. Secure the wiring harness of the side airbag module with the fastener.
4. Connect the connector and the clamp of the seat heater. (For the model with the seat heater)
5. Install the rubber band of the separate type front seat backrest cover LH.
6. Engage 2 hooks.
15. Installation of the front seat inner belt ASSY LH (driver's side)
16. Installation of the front seat inner belt ASSY RH (passenger's side)
17. Installation of the front seat cushion shield INN LH
1. Engage 2 claws and 5 guides, and install the front seat cushion shield INN LH.
18. Installation of the front seat cushion shield LH
1. Engage 4 claws, 5 guides, and the clip, and install the front seat cushion shield LH.
2. Install the screws.
19. Installation of the vertical adjuster handle LH (driver's side)
1. Install the vertical adjuster handle LH with the screw.
20. Installation of the reclining adjuster release handle LH
1. Engage the claw and install the reclining adjuster release handle LH.