Disassembly

Front Seat Assy

DISASSEMBLY

NOTE: The procedures described below are for the LH side. Unless otherwise specified, perform the work for the RH side referring to the procedures for the LH side.

1. Removal of the reclining adjuster release handle LH
1. Pull up the reclining adjuster release handle LH.







2. As shown in the figure, release the claw by using the fine flat tip screwdriver wrapped with protective tape, and remove the reclining adjuster release handle LH.







2. Removal of the vertical adjuster handle LH (driver's side)
1. Remove the screw and remove the vertical adjuster handle LH.







3. Removal of the front seat cushion shield LH
1. Remove 2 screws.
2. Release 4 claws, 5 guides, and the clip, and remove the front seat cushion shield LH.







4. Removal of the front seat cushion shield INN LH
1. Release 2 claws, 4 guides, and the clip, and remove the front seat cushion shield INN LH.

5. Removal of the front seat inner belt ASSY LH (driver's side)
6. Removal of the front seat inner belt ASSY RH (passenger's side)







7. Removal of the front seat backrest ASSY LH
1. Release 2 hooks.







2. Remove the rubber band of the separate type front seat backrest cover LH.







3. Disconnect the connector and the clamp of the seat heater. (For the model with the seat heater)







4. Release the fastener and disconnect the wiring harness of the side airbag module LH.







5. Release the claw and 4 clamps, and disconnect the wiring harness of the side airbag module ASSY LH.







6. Using the torque socket wrench (T40), remove 4 bolts, and remove the front seat backrest ASSY LH from the front seat cushion ASSY LH.







8. Removal of the separate type front seat backrest cover with pad
1. Remove 5 hog rings.







2. Open 2 fasteners.
3. Turn over the separate type front seat backrest cover LH.







4. Release 2 hooks.







5. Remove the nut, and disconnect 3 brackets of the separate type front seat backrest cover LH.







6. Release 4 claws and remove 2 front seat headrest supports.
7. Remove the separate type front seat backrest cover with pad from the separate type front seat backrest frame ASSY LH.

9. Removal of the side airbag module LH







10. Removal of the separate type front seat backrest cover LH
1. Remove 14 hog rings, and remove the separate type front seat backrest cover LH from the separate type front seat backrest pad LH.

11. Removal of the separate type front seat cushion cover with pad







1. Release the claw, and disconnect the connector of the occupant detection sensor. (passenger's side)







2. Release the claw and 3 clamps, and disconnect the wiring harness of the seat heater. (For the model with the seat heater)
3. Release the hooks, and remove the separate type front seat cushion cover with pad from the separate type front seat cushion frame ASSY LH. (driver's side)







4. Release the hooks, and remove the separate type front seat cushion cover with pad from the separate type front seat cushion frame ASSY RH. (passenger's side)










12. Removal of the separate type front seat cushion cover LH
1. Remove 2 hog rings.







2. Remove 12 hog rings, and remove the separate type front seat cushion cover LH from the separate type front seat cushion pad LH.







13. Removal of the front seat cushion shield LWR LH (driver's side)
1. Remove the screw.
2. Release the hook.
3. Release the clip, and remove the front seat cushion shield LWR LH.

14. Removal of the front seat cushion shield LWR LH (driver's side)

NOTE: Remove it in the same manner as the RH side.







15. Removal of the front seat cushion edge protector LH
1. Remove the screw.
2. Release 3 claws and remove the front seat cushion edge protector LH.

16. Removal of the front seat cushion edge protector LH

NOTE: Remove it in the same manner as the RH side.







17. Removal of the seat track adjusting handle
1. Remove 2 springs with a screwdriver, and remove the seat track adjusting handle from the separate type front seat cushion frame ASSY LH.







18. Removal of the reclining adjuster release band (passenger's side)
1. Remove the screw and remove the reclining adjuster release band.







19. Removal of the seat track cover OUT RH
1. Release 2 claws and remove the seat track cover OUT RH.

NOTE: Remove the both covers by following the same procedures.







20. Removal of the front seat cushion protector No.1
1. Release 2 claws and remove the front seat cushion protector No.1.

NOTE: Remove the both covers by following the same procedures.