Operation CHARM: Car repair manuals for everyone.
Home >> Suzuki Truck >> 2012 >> Equator 4WD V6-4.0L >> Repair and Diagnosis >> Transmission and Drivetrain >> Manual Transmission/Transaxle >> Service and Repair >> Overhaul >> Gear Components >> Disassembly and Assembly >> Part 2

Part 2




Gears Components: Disassembly and Assembly

Part 2

8) Press in 4th main gear using Tool.






CAUTION:
- Do not reuse 4th main gear.
- Be careful with the orientation 4th main gear.

9) Press in mainshaft bearing using Tool.











CAUTION:
Be careful with the orientation mainshaft bearing.

10) Press in reverse main gear bushing using Tool.











11) Press in 3rd gear bushing using Tool.











12) Install 3rd-4th synchronizer hub assembly according to the following.
a) Install 3rd-4th coupling sleeve to 3rd-4th synchronizer hub.

CAUTION:
- Do not reuse 3rd-4th synchronizer hub and 3rd-4th coupling sleeve.
- Replace 3rd-4th synchronizer hub and 3rd-4th coupling sleeve as a set.
- Be careful with the orientation 3rd-4th coupling sleeve.






b) Install spread springs and shifting inserts to 3rd-4th synchronizer hub.






CAUTION:
- Do not install spread spring hook onto the same shifting insert.
- Be careful with the shape of reverse shifting insert to avoid misassembly.






c) Press in 3rd-4th synchronizer hub assembly, 3rd inner baulk ring, 3rd synchronizer cone, 3rd outer baulk ring, 3rd counter gear and 3rd needle bearing using Tool.











CAUTION:
- Apply gear oil to 3rd inner baulk ring, 3rd synchronizer cone, 3rd outer baulk ring and 3rd needle bearing, hole spline of 3rd-4th synchronizer hub.
- Replace 3rd inner baulk ring, 3rd synchronizer cone and 3rd outer baulk ring as a set.
- Be careful with the orientation 3rd-4th coupling sleeve.

NOTE:
4th baulk ring has three spaces that one gear tooth is missing but 3rd baulk ring doesn't.





13) Press in 4th counter gear thrust washer, 4th gear bushing, 4th needle bearing, 4th counter gear, 4th outer baulk ring,4th synchronizer cone and 4th inner baulk ring using Tool.











CAUTION:
- Apply gear oil to 4th needle bearing, 4th outer baulk ring, 4th synchronizer cone and 4th inner baulk ring.
- Replace 4th outer baulk ring, 4th synchronizer cone and 4th inner baulk ring as a set.
- Be careful with the orientation 4th counter gear thrust washer.

NOTE:
4th baulk ring has three spaces that one gear tooth is missing but 3rd baulk ring doesn't.





14) Press in counter rear bearing inner race using Tool.











CAUTION:
Be careful with the orientation counter rear bearing inner race.

15) Install main drive gear bearing according to the following.
a) Press in main drive gear bearing using Tool.











CAUTION:
Be careful with the orientation main drive gear bearing.

b) Select and install a snap ring to main drive gear bearing so that the end play comes within the standard value. Refer to [Service Data and Specifications] Mechanical Specifications.











CAUTION:
Do not reuse snap ring.

16) Install breather to adapter plate.






CAUTION:
- Do not reuse breather.
- Be careful with the orientation breather.

17) Install magnet to adapter plate.






CAUTION:
Be careful with the orientation magnet.

18) Install baffle plate to adapter plate, and then tighten bolt to the specified torque. Refer to [Transmission Assembly: Disassembly and Assembly] Transmission Disassembly and Assembly.





19) Install main drive gear assembly, mainshaft assembly and counter gear assembly according to the following.
a) Install main pilot bearing, pilot bearing spacer and 5th baulk ring to main drive gear.





b) Install main drive gear assembly, mainshaft assembly and counter gear assembly combined in one unit to adapter plate using brass bar.
20) Install Tool to adapter plate, and then position in a vise.











CAUTION:
Do not directly secure mating surface of adapter plate in a vise.

21) Install snap ring to mainshaft bearing.






CAUTION:
Do not reuse snap ring.

22) Install counter rear bearing to adapter plate using Tool.











23) Install counter rear bearing spacer to counter gear.

CAUTION:
When installing counter rear bearing spacer, groove should face to the rear side.

24) Install bearing retainer according to the following.
a) Install bearing retainer to adapter plate.





b) Apply recommended thread locking sealant to threads of bolts, and then tighten bolts to the specified torque. Refer to [Transmission Assembly: Disassembly and Assembly] Transmission Disassembly and Assembly.
- Use Genuine Medium Strength Thread Locking Sealant or the equivalent. Refer to [Recommended Chemical Products and Sealants] Recommended Chemical Products and Sealants.
25) Install reverse synchronizer hub assembly according to the following.
a) Install reverse coupling sleeve to reverse synchronizer hub.

CAUTION:
- Do not reuse reverse coupling sleeve and reverse synchronizer hub.
- Replace reuse reverse coupling sleeve and reverse synchronizer hub as a set.
- Be careful with the orientation reverse coupling sleeve.





- Be careful with the orientation reverse synchronizer hub.






b) Install spread springs to shifting inserts to reverse synchronizer hub.






CAUTION:
- Do not install spread spring hook onto the same shifting insert.
- Be careful with the shape of 1st-2nd, 3rd-4th and 5th-6th shifting insert to avoid misassembly.






c) Install snap ring to reverse synchronizer hub.






CAUTION:
- Do not reuse snap ring.
- Do not align the snap ring notch with synchronizer hub groove when assembling.

d) Press in reverse synchronizer hub assembly, reverse baulk ring, reverse main gear and reverse main needle bearing using Tools.











CAUTION:
Apply gear oil to reverse baulk ring and reverse main needle bearing.

NOTE:
Reverse baulk ring has three spaces that two gear teeth are missing, and each space has small ditch for identification as shown.





26) Select and install a snap ring so that the end play comes within the standard value. Refer to [Service Data and Specifications] Mechanical Specifications.











CAUTION:
Do not reuse snap ring.

27) Press in reverse counter gear using Tool.











CAUTION:
- Do not reverse counter gear.
- Be careful with the orientation counter gear.

28) Select and install a snap ring so that the end play comes within the standard value. Refer to [Service Data and Specifications] Mechanical Specifications.











CAUTION:
Do not reuse snap ring.

29) Install reverse idler shaft assembly according to the following.
a) Install reverse idler needle bearing, reverse idler gear and reverse idler thrust washer to reverse idler shaft.

CAUTION:
Apply gear oil to reverse idler needle bearing.

b) Install reverse idler shaft assembly to adapter plate.






pro multis · About Operation CHARM