System Inspection

POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS EQUIPPED)

Step 1 - 10:

Step 11 - 13:

INSPECTION

POWER DOOR LOCK OPERATION
1. With the driver side door key turned LOCK, check all power doors are locked.
2. With the driver side door key turned UNLOCK, check only the driver side power door is unlocked.
Turn the driver side door key to UNLOCK again within 5 seconds, check all power doors are unlocked.

If check result of Step 1) and Step 2) is satisfactory, this operation is OK.

KEYLESS ENTRY OPERATION
1. With the IG switch OFF and all doors closed, push LOCK button on transmitter. Check all power doors are locked.
2. Push UNLOCK button on transmitter. Check only driver side power door is unlocked.
3. Push UNLOCK button on transmitter again within 5 seconds. Check all power doors are unlocked.
But if any door is not opened within 30 seconds after power door(s) unlocked, all power doors are locked again automatically.

If check result of Step 1) to Step 3) is satisfactory, this operation is OK.

HAZARD WARNING LIGHTS OPERATION
1. Check that hazard warning tights flash one time when power doors are locked by pushing LOCK button on transmitter.
2. Check that hazard warning lights flash two times when power door(s) is (are) unlocked by pushing UNLOCK button on transmitter.

If check result of Step 1) and Step 2) is satisfactory, this operation is OK.

INTERIOR LIGHT OPERATION
1. With the IG switch OFF and all doors closed, push UNLOCK button on transmitter. Check that interior light stays on for 20 seconds.
2. Push UNLOCK button again, turn IG switch ON within 20 seconds.
Check that interior light goes out.

If check result of Step 1) and Step 2) is satisfactory, this operation is OK.




POWER DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect negative cable at battery.
2. Disconnect coupler of power door lock and keyless entry controller.
3. Use a 12 V battery to connect its (+) terminal to terminal L07-1, and its (-) terminal to terminal L07-2 and L07-3. Check all power doors are locked.

If check result is satisfactory, this circuit is OK.




POWER SUPPLY AND GROUNDING CIRCUIT
1. Disconnect negative cable at battery.
2. Disconnect coupler of power door lock and keyless entry controller, and connect negative cable at battery.




3. Check that the voltage and resistance between following terminals are specifications.

If check result is satisfactory, this circuit is OK.




DOOR LOCK KEY AND POWER DOOR LOCK SWITCH CIRCUIT
1. Disconnect negative cable at battery.
2. Disconnect coupler of power door lock and keyless entry controller.




3. Check for continuity between following terminals at each condition.

If check result is satisfactory, this circuit is OK.




IGNITION SWITCH AND DOOR SWITCH CIRCUIT
1. Disconnect negative cable at battery.
2. Disconnect coupler of power door lock and keyless entry controller, and connect negative cable at battery.




3. Check that the voltage and resistance between following terminals are specifications.

If check result is satisfactory, this circuit is OK.




DOOR KNOB SWITCH AND HAZARD WARNING LIGHTS CIRCUIT
1. Disconnect negative cable at battery.
2. Disconnect coupler of power door lock and keyless entry controller, and connect negative cable at battery.




3. Check that the voltage and resistance between following terminals are specifications.

If check result is satisfactory, this circuit is OK.




INTERIOR LIGHT AND IGNITION SWITCH CIRCUIT
1. Disconnect negative cable at battery.
2. Disconnect coupler of power door lock and keyless entry controller, and connect negative cable at battery.




3. Check that the voltage between following terminals are specification.

If check result is satisfactory, this circuit is OK.

POWER DOOR LOCK SWITCH
Refer to POWER DOOR LOCK SWITCH INSPECTION of POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED).

KEY CYLINDER SWITCH (DRIVER SIDE)
Refer to KEY CYLINDER SWITCH (DRIVER SIDE) INSPECTION of POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED).

POWER DOOR LOCK ACTUATOR
Refer to POWER DOOR LOCK ACTUATOR INSPECTION of POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED).