P0138
DTC P0138: HO2S Circuit High Voltage Sensor 2Wiring Diagram:
Circuit Description
In order to control emissions, a catalytic converter is used to convert harmful emissions into harmless water vapor and carbon dioxide.
The Engine Control Module (ECM) has the ability to monitor this process by using a Heated Oxygen Sensor 2 (HO2S2). The HO2S2, located in the exhaust stream past the catalytic converter, produces an output signal which indicates the storage capacity of the catalyst. This in turn indicates the catalyst's ability to convert exhaust emissions effectively. If the catalyst is functioning properly, the HO2S2 signal will be far less active than the signal produced by the Heated Oxygen Sensor 1 (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is damaged, the entire HO2S2 assembly must be replaced. Do not attempt to repair the wiring, connector, or terminals. In order for the sensor to function properly, it must have a clean air reference provided to it. This clean air reference is obtained by way of the HO2S2 wire(s). Any attempt to repair the wires, connector, or terminals could result in the obstruction of the air reference and degrade the HO2S2 performance.
Conditions for Setting the DTC
- HO2S2 voltage is greater than 0.95 V.
- Engine Coolant Temperature (ECT) is greater than 60 °C (140 °F).
- System voltage is greater than 10 V.
- 3 seconds delay after in Closed Loop and airflow is greater than 2 g/sec.
- Engine run time is greater than 10 seconds.
Action Taken When the DTC Sets
- The Malfunction Indicator Lamp (MIL) will illuminate.
- The ECM will record operating conditions at the time the diagnostic fails. This information will be stored in the Freeze Frame and Failure Records buffers.
- A history DTC is stored.
Conditions for Clearing the MIL/DTC
- The MIL will turn OFF after four consecutive ignition cycles in which the diagnostic runs without a fault.
- A history DTC will clear after 40 consecutive warm up cycles without a fault.
- The DTC(s) can be cleared by using the scan tool.
- Disconnecting the ECM battery feed for more than 10 seconds.
Diagnostic Aids
Check for the following conditions:
- Rich exhaust - An overly rich exhaust may load the catalyst, causing high HO2S2 signal voltages.
- Silicon contamination - A false rich condition may be caused by silicone contamination of the HO2S2. This will be indicated by a powdery white deposit on the sensor.
- Faulty HO2S2 - If HO2S2 is internally shorted, the HO2S2 voltage displayed on a scan tool will be over 1 V. Disconnect the HO2S2 and jumper the sensor low circuit to engine ground, if the displayed voltage goes from over 1,000 mV to around 450 mV, replace the HO2S2.
- Intermittent test - Observe HO2S2 on the scan tool while moving related connectors and wiring harness with the key in the ON position. If the failure is induced, the HO2S2 display will change. This may help isolate the location of the malfunction.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
1. The On-Board Diagnostic (OBD II) System Check prompts the technician to complete some basic checks and store the Freeze Frame and Failure Records data on the scan tool if applicable. This creates an electronic copy of the data taken when the malfunction occurred.
The information is then stored on the scan tool for later reference.
2. This step determines if DTC P0138 is the result of a hard failure or an intermittent condition.
3. Disconnecting the HO2S2 and jumpering the sensor signal circuit and the sensor low circuit to ground should cause the scan tool to display HO2S2 voltage below 100 mV (0.1 V). If the signal voltage is still high, the ECM is malfunctioning.
4. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM reprogramming.
Step 1-10:
Troubleshooting