B1363

DTC B1363 / B1367: Curtain Air Bag Circuit Shorted to Ground

DTC B1363: Curtain Air Bag Circuit Shorted to Ground (Driver Side)

DTC B1367: Curtain Air Bag Circuit Shorted to Ground (Passenger Side)

Wiring Diagram

Refer to B1361 DTC B1361 / B1365: Curtain Air Bag Circuit High Resistance:Advanced Air Bag.

DTC Detecting Condition and Trouble Area






DTC Troubleshooting



1.
Was "Air Bag Diagnostic System Check Flow" performed?
YES
Go to Step 2.
NO
Go to Air Bag Diagnostic System Check Flow:Advanced Air Bag.

2. Driver-side / passenger-side curtain air bag circuit check

With ignition switch turned OFF, remove rear quarter upper trim (hatchback model) or rear pillar inner trim (sedan model) of applicable side and disconnect applicable curtain air bag (inflator) module connector.
Disconnect SDM connector "L04".
Check for proper connection to SDM connector at terminal "L04-19" and "L04-20" (for DTC B1363) or terminal "L04-21" and "L04-22" (For DTC B1367).
Check for proper connection to applicable curtain air bag (inflator) module connector at terminal in its connector.
If OK, release shorting bar in SDM connector inserting release tool (1) included in special tool (A).
Special Tool

(A): 09932-76010

Measure resistance between "L04-19" terminal and body ground, and between "L04-20" terminal and body ground (for DTC B1363).
Measure resistance between "L04-21" terminal and body ground, and between "L04-22" terminal and body ground (for DTC B1367).






Is each measured resistance infinity?
YES
Substitute a known-good SDM and recheck.
NO
For hatchback model: Go to Step 3.
For sedan model:
Repair "YEL/GRN" or "YEL/BLU" circuit for short to ground at floor harness. (for DTC B1363)
Repair "BLK/YEL" or "BRN/YEL" circuit for short to ground at floor harness. (for DTC B1367)

3. Floor harness circuit check (hatchback model)

With ignition switch turned OFF, remove rear inner trim of right side and disconnect "L395" connector.
Check for proper connection to applicable curtain air bag at terminal in "L395" connector.
If OK, release shorting bar in SDM connector inserting release tool (1) included in special tool (A).
Special Tool

(A): 09932-76010

Measure resistance between "L04-19" terminal and body ground, and between "L04-20" terminal and body ground (for DTC B1363).
Measure resistance between "L04-21" terminal and body ground, and between "L04-22" terminal and body ground (for DTC B1367).






Is each measured resistance infinity?
YES
DTC B1363: Repair "YEL/GRN" or "YEL/BLU" circuit for short to ground at driver-side curtain air bag harness.
DTC B1367: Repair "BLK/YEL" or "BRN/YEL" circuit for short to ground at passenger-side curtain air bag harness.
NO
DTC B1363: Repair "YEL/GRN" or "YEL/BLU" circuit for short to ground at floor harness.
DTC B1367: Repair "BLK/YEL" or "BRN/YEL" circuit for short to ground at floor harness.

NOTE:

Upon completion of inspection and repair work, perform the following items.

- Reconnect all air bag system components, ensure all components are properly mounted.
- Clear DTCs referring to DTC Clearance DTC Clearance:Advanced Air Bag
, if any.
- Repeat Air Bag Diagnostic System Check Air Bag Diagnostic System Check:Advanced Air Bag
to confirm that the trouble has been corrected.