Valve Clearance: Testing and Inspection
INSPECTIONHINT: Inspect and adjust the valve clearance when the engine is cold.
1. REMOVE INTAKE AIR CONNECTOR
2. REMOVE PCV HOSES
3. Except California Spec.:
DISCONNECT HIGH-TENSION CORDS FROM SPARK PLUGS
4. California Spec.:
REMOVE IGNITION COILS (WITH IGNITER)
NOTICE: Pulling on or bending the cords may damage the conductor inside.
5. DISCONNECT ENGINE WIRE
a) w/ A/C:
Disconnect the A/C compressor connector.
b) Disconnect the oil pressure sensor connector.
c) Disconnect the ECT sender gauge connector.
d) Except California Spec.:
Disconnect the ignition coil connector.
e) Disconnect the 4 engine wire clamps and engine wire.
6. REMOVE CYLINDER HEAD COVER
Remove the 10 bolts, 10 seal washers, cylinder head cover and gasket.
7. SET NO.1 CYLINDER TO TDC/COMPRESSION
a) Turn the crankshaft pulley clockwise and align its groove with the "0" mark on the timing chain cover.
b) Check that the timing marks (1 and 2 dots) of the camshaft drive and driven gears are in straight line on the cylinder head surface as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) and align the marks as above.
8. INSPECT VALVE CLEARANCE
a) Check only the valves indicated.
1) Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
2) Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.
Valve clearance (Cold):
b) Turn the crankshaft pulley 1 revolution (360°) and align its groove with timing mark "O" of the timing chain cover.
c) Check only the valves indicated as shown. Measure the valve clearance. (See procedure in step (a))
9. ADJUST VALVE CLEARANCE
a) Remove the adjusting shim.
1) Turn the crankshaft to position the cam lobe of the camshaft on the adjusting valve upward.
2) Position the notch of the valve lifter toward the spark plug side.
3) Using SST (A), press down the valve lifter and place SST (B) between the camshaft and valve lifter flange. Remove SST (A).
SST 09248-55040 (09248-05410, 09248-05420)
HINT: Apply SST (B) at slight angle on the side marked with "9", at the position shown in the illustration.
4) Remove the adjusting shim with a small screwdriver and magnetic finger.
b) Determine the replacement adjusting shim size by these Formula or Charts:
1) Using a micrometer, measure the thickness of the removed shim.
2) Calculate the thickness of a new shim so that the valve clearance comes within the specified value.
T Thickness of removed shim
A Measured valve clearance
N Thickness of new shim
Intake: N = T + (A - 0.20 mm (0.008 inch)
Exhaust: N = T + (A - 0.30 mm (0.012 inch)
3) Select a new shim with a thickness as close as possible to the calculated value.
HINT: Shims are available in 17 sized in increments of 0.05 mm (0.0020 inch), from 2.50 mm (0.0984 inch) to 3.30 mm (0.1299 inch).
c) Install a new adjusting shim.
1) Place a new adjusting shim on the valve lifter.
2) Using SST (A), press down the valve lifter and remove SST (B).
SST 09248-55040 (09248-05410, 09248-05420)
d) Recheck the valve clearance.
10. REINSTALL CYLINDER HEAD COVER
11. RECONNECT ENGINE WIRE
12. Except California Spec.:
REINSTALL HIGH-TENSION CORDS TO SPARK PLUGS
13. California Spec.:
REINSTALL IGNITION COILS (WITH IGNITER)
14. REINSTALL PCV HOSES
15. REINSTALL INTAKE AIR CONNECTOR