Power Adjuster

DISASSEMBLY

1. REMOVE HEADREST




2. REMOVE FRONT SEAT CUSHION SHIELD
a. Remove the screw.
b. Using a screwdriver, remove the front seat cushion shield, then disconnect the connector.

HINT: Tape the screwdriver tip before use.

c. w/ Lumber support:
Remove the 2 screws and lumber support switch.

3. REMOVE SLIDE KNOB AND RECLINING KNOB
Using a screwdriver, remove the slide knob and reclining knob.

HINT: Tape the screwdriver tip before use.




4. REMOVE SWITCH BASE
Using a screwdriver, remove the switch base.

HINT: Tape the screwdriver tip before use.




5. REMOVE FRONT SEAT CUSHION COVER
Using a screwdriver, remove the front seat cushion cover.

HINT: Tape the screwdriver tip before use.




6. REMOVE FRONT SEAT CUSHION INNER SHIELD
Remove the screw and front seat cushion inner shield.

7. REMOVE FRONT SEAT INNER BELT
Remove the bolt and front seat inner belt.

Torque: 42 N.m (430 kg.cm, 31 ft.lb)




8. REMOVE SEAT CUSHION FRONT SHIELD
Using a screwdriver, remove the seat cushion front shield.

HINT: Tape the screwdriver tip before use.




9. REMOVE SEAT CUSHION LOWER SHIELD
a. Remove the screw.
b. Remove the seat cushion lower shield as shown in the illustration.
c. Employ the same manner described above to the other side.




10. REMOVE POWER SEAT SWITCH
a. Unlatch the front portion of seat cushion cover hook.
b. Turn over the left part of seat cushion cover.
c. Remove the 3 screws.
d. Disconnect the 2 connectors and remove the power seat switch.

11. REMOVE SEAT CUSHION ASSEMBLY
a. Disconnect the connector.
b. Remove the 4 bolts and seat cushion assembly.

Torque: 19 N.m (195 kg.cm 14 ft.lb)




12. REMOVE SEAT CUSHION COVER
a. Unlatch the seat cushion cover hooks, then remove the seat cushion frame from the seat cushion cover with pad.
b. Remove the seat cushion cover from the seat cushion pad.

HINT: At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.




13. REMOVE SEATBACK ASSEMBLY
a. Remove the 3 hog rings as shown in the illustration.

HINT: At the time of reassembly, please refer to the following item.
When installing hog rings, take care to prevent wrinkles as little as possible.

b. Remove the 4 bolts and seatback assembly.

Torque: 43 N.m (440 kg.cm, 32 ft.lb)

14. REMOVE ARMREST
a. Open the fastener.
b. Remove the bolt and armrest.

Torque: 37 N.m (380 kg.cm, 27 ft.lb)

c. Remove the armrest cover.

15. REMOVE SEATBACK FRAME
a. Turn over the seatback cover upward.




b. w/ Side airbag assembly:
Remove the bolt and disengage the seat cover hangers from the seatback frame.

Torque: 5.5 N.m (56 kg.cm, 49 in.lb)

NOTE: Be careful not to damage the side airbag assembly.




c. Remove the 2 hog rings as shown in the illustration.
d. Remove the 2 headrest supports.

HINT: At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

e. Remove the 2 hog rings and seatback cover from the seatback pad with frame.

HINT: At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

f. Remove the seatback frame from the seatback pad.

16. W/ Lumber support: REMOVE LUMBER SUPPORT ADJUSTER




17. REMOVE SEAT CUSHION INSIDE COVER
a. Remove the 2 screws and seat cushion inside cover.
b. Employ the same manner described above to the other side.

REASSEMBLY
Reassembly is in the reverse order of disassembly.