Rear No.1 Seat (LH)
DISASSEMBLY1. REMOVE HEADREST
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
3. REMOVE NO. 1 RECLINING COVERS
a. Zip the seat cushion cover open.
b. Remove the 2 screws and 2 No. 1 reclining covers.
4. REMOVE SEAT CUSHION UNDER COVER
a. Remove the 2 screws and 2 seat cushion under covers.
b. Remove the 10 screws and seat cushion under cover sub-assembly.
5. REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE
Remove the clamp and No. 1 fold seat lock control cable as shown in the illustration.
6. REMOVE SEATBACK ASSEMBLY
a. Remove the 3 screws and seat belt reclining detecting part.
HINT: At the time of reassembly, please refer to the following items.
- Tighten the 2 screws on the seatback side.
- Fold down the seatback forward and raise it up to the first lock position.
- Turn A to the rear side of the seat cushion for initial positioning.
- Check visually that the reference holes are penetrated.
- Tighten the screws on the cushion side of seat belt reclining detecting part.
b. Remove the reclining connecting wire of LH side edge.
c. Remove the reclining connecting wire of RH side edge.
d. Remove the 4 bolts and seatback assembly.
Torque: 41 N.m (420 kgf.cm, 30 ft.lbf)
7. REMOVE ARMREST
8. REMOVE SEATBACK FRAME
a. Using a screwdriver, remove the rear seat shoulder belt cover.
HINT: Tape the screwdriver tip before use.
b. Remove the 4 headrest supports
c. Disengage the hooks, remove the seatback frame.
9. REMOVE SEAT ADJUSTER CONTROL CABLE
Remove the 2 clamps and seat adjuster control cable.
10. REMOVE REAR SEAT OUTER BELT
a. Remove the 2 bolts and rear seat shoulder belt guide.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
HINT: At the time of reassembly, please refer to the following item.
Install the shoulder belt guide to the seatback frame with a sit the guide facing to the rear side of the vehicle.
b. Remove the nut, 3 clamps and rear seat outer belt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
11. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover.
HINT: At the time of reassembly, please refer to the following item.
When instaling hog rings, take care to prevent wrinkles as little as possible.
12. REMOVE SEAT CUSHION FRAME
Remove the hog rings and seat cushion frame.
HINT: At the time of reassembly, please refer to the following item.
When instaling hog rings, take care to prevent wrinkles as little as possible.
13. REMOVE REAR NO. 1 SEAT ADJUSTER
a. Remove the 2 bolts and rear No. 1 seat outer adjuster.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Remove the 2 bolts and rear No. 1 seat inner adjuster.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
c. Remove the 4 screws and 2 hinges covers from the rear No. 1 seat outer and inner adjusters.
d. Remove the 2 screws and 2 reclining inner covers from the rear No. 1 seat outer and inner adjuster.
14. REMOVE REAR SEAT STAY
Remove the 2 bolts and rear seat stay.
15. REMOVE REAR SEAT CUSHION HINGE
a. Using a screwdriver, remove the spring nut and E-rings.
b. Remove the 2 hinge pins, 2 cushion spacers, 2 cushion support springs and 2 rear seat cushion hinges.
16. REMOVE LH REAR SEAT LOCK
Unfasten the bolt, then remove the inner belt and LH rear seat lock.
17. REMOVE RH REAR SEAT LOCK
a. Remove the screw and rear seat lock cover.
b. Remove the bolt, seat belt anchor and inner belt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
c. Remove the RH rear seat lock.
REASSEMBLY
REASSEMBLY is in the reverse order of disassembly.