Rear Seat
OVERHAULHINT: Installation is in the reverse order of removal. But, the installation is indicated only when it has a point.
1. REMOVE REAR SEAT ASSY RH
a. Using a screwdriver, remove the front part of deck board assembly.
HINT: Tape the screwdriver tip before use.
b. Remove the 4 clips.
c. Using a screwdriver, remove the 2 seat track covers.
HINT: Tape the screwdriver tip before use.
d. Remove the bolt.
e. Remove the rear seat assembly RH.
NOTE: Be careful not to damage the body.
2. REMOVE REAR SEAT ASSY LH
a. Remove the 3 clips.
b. Using a screwdriver, remove the 2 seat track covers.
HINT: Tape the screwdriver tip before use.
c. Remove the rear seat assembly LH.
NOTE: Be careful not to damage the body.
3. REMOVE HEADREST ASSY, RR SEAT, RH
4. REMOVE REAR SEAT HEADREST ASSY CENTER
5. REMOVE REAR SEAT HEADREST ASSY RH
6. REMOVE REAR SEAT BACK BOARD CARPET ASSY RH
a. Using a screwdriver, remove the rear seat back board carpet assembly RH.
HINT: Tape the screw driver tip before use.
7. REMOVE REAR SEAT BACK BOARD CARPET ASSY LH
a. Using a screwdriver, remove the rear seat back board carpet assembly LH.
HINT: Tape the screw driver tip before use.
8. REMOVE RECLINING COVER PROTECTOR RH
a. Remove the 4 bolts and the separate type rear seat cushion assembly.
9. REMOVE RECLINING COVER PROTECTOR LH
a. Remove the 4 bolts and the separate type rear seat cushion assembly LH.
10. REMOVE CUSHION ASSY, RR SEAT, RH
11. REMOVE RECLINING COVER PROTECTOR RH
12. REMOVE RECLINING COVER PROTECTOR LH
a. Remove the 4 bolts.
b. Disconnect the seat lock control cable from the adjuster, and remove the separate type rear seat cushion assembly RH.
13. REMOVE CUSHION ASSY, RR SEAT LH
a. Remove the 4 bolts.
b. Disconnect the seat lock control cable from the adjuster, and remove the separate type rear seat cushion assembly LH.
14. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
15. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
a. Disengage the seat cushion cover hook.
b. Remove the hog rings and separate type rear seat cushion frame LH.
c. Remove the hog rings and separate type rear seat cushion cover LH.
d. Remove the seat wires from the separate type rear seat cushion cover LH.
16. REMOVE REAR SEAT ARMREST ASSY CENTER
a. Remove the center armrest hinge cover.
b. Remove the bolt and rear seat armrest assembly center.
17. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSY RH
a. Disengage the seat cushion cover hook.
b. Remove the hog rings and separate type rear seat cushion frame RH.
c. Remove the hog rings and separate type rear seat cushion cover RH.
d. Remove the seat wires from the separate type rear seat cushion cover RH.
18. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSY RH
a. Using a screwdriver, remove the cover.
HINT: Tape the screw driver tip before use.
b. Remove the 2 screws.
c. Disconnect the seat lock control cable, remove the rear seat lock control lever RH.
19. REMOVE REAR SEAT RECLINING COVER NO.1 RH
a. Using a screwdriver, remove the cover.
HINT: Tape the screwdriver tip before use.
b. Remove the 2 screws.
c. Disconnect the seat lock control cable, remove the rear seat lock control lever LH.
20. REMOVE REAR SEAT RECLINING COVER NO.1 RH
a. Remove the seat back hooks and 4 clips.
b. Remove the 4 headrest supports.
c. Remove the seat back cover with pad from the seat back frame.
d. Remove the hog rings and seat back RH cover from the seat back pad RH.
21. REMOVE BACK ASSY, RR SEAT, RH
22. REMOVE REAR SEAT RECLINING COVER NO.2 RH
23. REMOVE REAR SEAT RECLINING COVER NO.2 RH
24. REMOVE BACK ASSY, RR SEAT LH
25. REMOVE REAR SEAT SHOULDER BELT COVER
a. Remove the seat back hooks and 4 clips.
b. Remove the 4 headrest supports.
c. Remove the seat back cover with pad from the seat back frame.
d. Remove the hog rings and seat back cover LH from the seat back pad LH
26. REMOVE SEPARATE TYPE REAR SEAT BACK COVER
27. REMOVE SEPARATE TYPE REAR SEAT BACK COVER
28. REMOVE RECLINING REMOTE CONTROL CABLE ASSY
a. Remove the screw and rear seat cushion moulding RH.
29. REMOVE RECLINING REMOTE CONTROL CABLE ASSY
30. REMOVE SEAT TRACK HANDLE SUB-ASSY RH
31. REMOVE SEAT TRACK HANDLE SUB-ASSY LH
32. REMOVE REAR SEAT BELT ASSY INNER
33. REMOVE REAR SEAT BELT ASSY INNER
34. REMOVE REAR SEAT CUSHION MOULDING RH
a. Remove the screw.
b. Remove the reclining remote control cable assembly LH.
35. REMOVE REAR SEAT CUSHION MOULDING LH
a. Remove the screw.
b. Remove the reclining remote control cable assembly RH.
36. REMOVE REAR SEAT CUSHION MOULDING REAR RH
a. Remove the screw and rear seat cushion moulding LH.
37. REMOVE REAR SEAT CUSHION MOULDING REAR LH
a. Remove the screw and rear seat cushion moulding rear RH.
38. REMOVE RECLINING CONNECTING ROD SUB-ASSY RH
a. Remove the screw and rear seat cushion moulding rear LH.
39. REMOVE RECLINING CONNECTING PIPE RH
a. Install the seat wires to the rear seat back cover.
b. Install the separate type rear seat back cover RH with pad to the seat back spring with the new hog rings.
c. Install the separate type rear seat back cover RH part of patch back facing with the 4 clips.
HINT: When installing hog rings, take care to prevent wrinkles as little as possible.
40. REMOVE RECLINING CONNECTING PIPE RH
a. Install the seat wires to the rear seat back cover.
b. Install the separate type rear seat back cover LH with pad to the seat back spring with new hog rings.
c. Install the separate type rear seat back cover LH part of patch back facing with the 4 clips.
HINT: When installing hog rings, take care to prevent wrinkles as little as possible.
41. INSTALL RECLINING CONNECTING ROD SUB-ASSY RH
a. Mount the rear seat back assembly RH on the seat adjuster assembly.
b. Connect the reclining remote control cable and rear seat adjuster.
c. Install the 4 bolts.
Torque: 55.0 N.m (561 kgf.cm, 41 ft.lbf)
d. Install the separate type rear seat back cover RH part of under hook.
42. INSTALL REAR SEAT BELT ASSY INNER
a. Install the rear seat belt assembly inner LH with the bolt.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)
43. INSTALL REAR SEAT BELT ASSY INNER
a. Adjust the reclining lock positions of the seat adjusters.
b. Place the adjusters on a spacers to adjust the seat rails in parallel.
c. Combine the lower seat back frame and reclining connecting pipe
d. Install the lower seat back frame and reclining connecting pipe.
e. Install the reclining connecting rod with the 4 bolts.
Torque: 18.0 N.m (184 kgf.cm, 13 ft.lbf)
44. INSTALL REAR SEAT BELT ASSY OUTER CENTER
45. INSTALL SEPARATE TYPE REAR SEAT BACK COVER
a. Remove the bolt.
b. Remove the rear seat belt assembly inner LH.
46. INSTALL SEPARATE TYPE REAR SEAT BACK COVER
a. Remove the bolt.
b. Remove the rear seat belt assembly inner RH.
47. INSTALL BACK ASSY, RR SEAT, RH
a. Install the rear seat belt assembly inner RH with the bolt.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)
48. CHECK SEAT RECLINING ADJUSTER LOCKS
a. Install the rear seat belt assembly outer center to the rear seat back RH with the nut.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)
49. INSTALL REAR SEAT BELT ASSY OUTER CENTER
a. Install the rear seat belt assembly outer center to the rear seat back RH part of anchor with the bolt.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)
50. INSTALL BACK ASSY, RR SEAT, LH
a. Mount the rear seat back assembly LH on the seat adjuster assembly.
b. Connect the reclining remote control cable and rear seat adjuster.
c. Install the 4 bolts.
Torque: 55.0 N.m (561 kgf.cm, 41 ft.lbf)
d. Install the separate type rear seat back cover LH part of the under hook.
51. INSTALL REAR SEAT ARMREST ASSY CENTER
Torque: 20 N.m (204 kgf.cm, 14 ft.lbf)
52. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
53. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
a. Install the seat wires to the rear seat cushion cover.
b. Install the separate type rear seat cushion cover RH with pad to the seat cushion spring with the hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as little as possible.
54. INSTALL CUSHION ASSY, RR SEAT, RH
a. Install the seat wires to the rear seat cushion cover.
b. Install the separate type rear seat cushion cover LH with pad to the seat cushion spring with new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as little as possible.
55. INSTALL CUSHION ASSY; RR SEAT; LH
a. Mount the separate type rear seat cushion assembly RH on the seat adjuster assembly.
b. Install the 4 bolts.
Torque:
Upper bolts: 37.0 N.m (378 kgf.cm, 27 ft.lbf)
Lower bolts: 18.0 N.m (183 kgf.cm, 13 ft.lbf)
56. INSTALL REAR SEAT ASSY RH
a. Mount the separate type rear seat cushion assembly LH on the seat adjuster assembly.
b. Install the 4 bolts.
Torque:
Upper bolts: 37.0 N.m (378 kgf.cm, 27 ft.lbf)
Lower bolts: 18.0 N.m (183 kgf.cm, 13 ft.lbf)
57. INSTALL REAR SEAT ASSY LH
a. Mount the rear seat assembly RH to the vehicle.
b. Tighten the 4 bolts.
Torque: 36.7 N.m (375 kgf.cm, 27 ft.lbf)