Rear Wiper and Washer
Rear Wiper And Washer:
REMOVAL
1. REMOVE REAR WIPER ARM
a. Open the cover.
b. Remove the nut and rear wiper arm.
Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)
c. Remove the rear wiper motor grommet.
2. REMOVE STEP LINER
Using a screwdriver, remove the step liner.
HINT: Tape the screwdriver tip before use.
3. REMOVE BACK DOOR PULL STRAP
a. Using a screwdriver, remove the strap cover.
HINT: Tape the screwdriver tip before use.
b. Remove the screw and back door pull strap.
4. REMOVE BACK DOOR CENTER GARNISH
Using a screwdriver, remove the back door center garnish.
HINT: Tape the screwdriver tip before use.
5. REMOVE BACK DOOR SIDE GARNISH
a. Using a screwdriver, remove the back door side garnish.
HINT: Tape the screwdriver tip before use.
b. Employ the same manner described above to the other side.
6. REMOVE BACK DOOR TRIM BOARD
a. Insert a screwdriver between the back door and back door time board to pry the back door trim board out.
NOTE: Be careful not to damage the back door and back door trim board.
HINT: Tape the screwdriver tip before use.
b. Pull the back door trim board to remove it as shown in the illustration.
7. REMOVE NO.1 SERVICE HOLE COVER
8. REMOVE NO.2 SERVICE HOLE COVER
9. REMOVE BACK DOOR GLASS
a. Open the back door glass until the bolts appear in the service hole.
b. Disconnect the connector.
c. Remove the 2 bolts and guide bracket.
d. Remove the 4 bolts and back door glass as shown in the illustration.
NOTE: Be careful not to drop the back door glass.
10. REMOVE POWER WINDOW REGULATOR
a. Disconnect the connector.
b. Disengage the connector and clamp.
c. Remove the 4 nuts and power window regulator.
HINT: Remove the power window regulator through the service hole.
11. REMOVE REAR WIPER MOTOR
a. Disconnect the connector.
b. Disengage the connector and clamp.
c. Remove the service hole plug.
d. Unfasten the 3 bolts, then remove the rear wiper motor.
12. REMOVE WASHER NOZZLE
a. Using a screwdriver, remove the washer nozzle.
HINT: Tape the screwdriver tip before use.
b. Disconnect the washer hose.
INSTALLATION
1. INSTALL WASHER NOZZLE
2. INSTALL REAR WIPER MOTOR
a. Install the rear wiper motor, then torque the 3 bolts.
Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)
b. Engage the connector and clamp.
c. Connect the connector.
3. INSTALL POWER WINDOW REGULATOR
Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)
4. INSTALL BACK DOOR GLASS
Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf)
5. INSTALL NO.2 SERVICE HOLE COVER
6. INSTALL NO.1 SERVICE HOLE COVER
7. INSTALL BACK DOOR TRIM BOARD
8. INSTALL BACK DOOR SIDE GARNISH
9. INSTALL BACK DOOR CENTER GARNISH
10. INSTALL BACK DOOR PULL STRAP
11. INSTALL STEP LINER
12. INSTALL REAR WIPER ARM
a. Install the rear wiper motor grommet as shown in the Illustration.
b. Operate the wiper once and turn the wiper switch OFF.
c. Install the wiper arm as shown in the illustration, then torque the nut.
Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)
d. Set the wiper arm to rise-up position as shown in the illustration.
e. Close the cover.