Rear No.2 Seat Assy

Rear No.2 Seat Assy:

OVERHAUL

HINT:
- The installation procedures are the removal procedures in reverse order. However, only installation procedures requiring additional information are included.
- A bolt without a torque specification is shown in the standard bolt chart.

1. REMOVE TONNEAU COVER ASSEMBLY (W/ TONNEAU COVER)
2. REMOVE DECK BOARD SUB-ASSEMBLY NO.2
3. REMOVE DECK BOARD SUB-ASSEMBLY NO.3
4. REMOVE DECK BOARD SUB-ASSEMBLY
5. REMOVE DECK FLOOR BOX REAR
6. REMOVE DECK SIDE TRIM BOX LH
7. REMOVE DECK SIDE TRIM BOX RH
8. REMOVE DECK BOARD BRACKET REINFORCEMENT
9. REMOVE RECLINING PEDAL COVER LH
a. Remove the screw and reclining pedal cover LH.

10. REMOVE RECLINING PEDAL COVER RH

HINT: Use the same procedures described for the LH side.

11. REMOVE REAR SEAT RECLINING COVER NO.2 LH
a. Remove the 2 screws and rear seat reclining cover No.2 LH.

12. REMOVE REAR SEAT RECLINING COVER NO.2 RH

HINT: Use the same procedures described for the LH side.

13. REMOVE REAR SEAT RECLINING COVER INNER LH
a. Remove the screw and rear seat reclining cover inner LH.

14. REMOVE REAR SEAT RECLINING COVER INNER RH

HINT: Use the same procedures described for the LH side.




15. REMOVE REAR NO.2 SEAT ASSEMBLY
a. Remove the 4 bolts and rear No.2 seat.




16. REMOVE REAR NO.2 SEAT LEG LH
a. Using a torx socket wrench (T45), remove the sub seat bolt.
b. Remove the 4 bolts and rear No.2 seat leg LH.

17. REMOVE REAR NO.2 SEAT LEG RH

HINT: Use the same procedures described for the LH side.




18. REMOVE NO.2 SEAT CUSHION COVER SUB-ASSEMBLY
a. Remove the 4 clips and hook.
b. Remove the hog rings and seat cushion cover together with the pad from the seat cushion frame.
c. Remove the hog rings and seat cushion cover from the seat cushion pad.

19. REMOVE REAR SEAT HEADREST ASSEMBLY




20. REMOVE HANDLE 3RD SEAT
a. Remove the 2 screws.
b. Disengage the 2 claws.
c. Disconnect the rear No.1 seat cable and remove the handle 3rd seat.




21. REMOVE NO.2 SEATBACK BOARD ASSEMBLY
a. Remove the 7 clips.
b. Disengage the 3 claws and remove the seatback board.

22. REMOVE NO.2 SEATBACK COVER ASSEMBLY
a. Remove the 2 headrest supports.
b. Remove the hog rings and seatback cover together with the pad from the seatback frame.
c. Remove the hog rings and seatback cover from the seatback pad.

23. REMOVE REAR SIDE SEAT BAND SUB-ASSEMBLY NO.2
24. REMOVE REAR SEAT COVER BEZEL NO.1
25. REMOVE REAR NO.1 SEAT LOCK CABLE ASSEMBLY
26. INSTALL REAR NO.1 SEAT LOCK CABLE ASSEMBLY
27. INSTALL REAR SEAT COVER BEZEL NO.1
28. INSTALL REAR SIDE SEAT BAND SUB-ASSEMBLY NO.2




29. INSTALL NO.2 SEATBACK COVER ASSEMBLY
a. Install the seatback cover to the seatback pad with new hog rings.
b. Install the seatback cover with the pad to the seatback frame with new hog rings.

HINT: When installing hog rings, take care to prevent wrinkles as little as possible.

30. INSTALL NO.2 SEATBACK BOARD ASSEMBLY
31. INSTALL HANDLE 3RD SEAT
32. INSTALL REAR SEAT HEADREST ASSEMBLY




33. INSTALL NO.2 SEAT CUSHION COVER SUB-ASSEMBLY
a. Install the seat cushion cover to the seat cushion pad with new hog rings.
b. Install the seat cushion cover with the pad to the seat cushion frame with new hog rings.

HINT: When installing the hog rings, take care to prevent wrinkles as much as possible.




c. Install the 4 clips and hook.




34. INSTALL REAR NO.2 SEAT LEG LH
a. Install the rear No. 2 seat leg LH with the sub seat bolt and 4 bolts.

Torque:
21 Nm (214 kgf.cm, 15 ft.lbf) for bolt A
42 Nm (428 kgf.cm, 31 ft.lbf) for bolt B
18 Nm (184 kgf.cm, 13 ft.lbf) for bolt C

35. INSTALL REAR NO.2 SEAT LEG RH

HINT: Use the same procedures described for the LH side.




36. INSTALL REAR NO.2 SEAT ASSEMBLY
a. Install the rear No.2 seat with the 4 bolts.

Torque: 37 Nm (377 kgf.cm, 27 ft.lbf)