Operation Check

OPERATION CHECK

1. NOTE WHEN CHECKING THE FOLLOWING
a. Power door lock/unlock function: This wireless door lock control function operates only when the following 4 conditions are met:
1. There is no key in the ignition key cylinder.
2. All the doors are closed.
3. The power door lock system is functioning normally.
4. The function has not been disabled by customization.

HINT: The unlock function operates even when any of the doors are open.

b. Remote panic function: This wireless control function operates only when the following condition is met:
1. The ignition switch is turned off.

HINT: The key can be inserted, however, the ignition switch must be turned off.

c. The wireless transmitter operational area differs depending on the situation.
1. The operational range differs depending on the user, the way the transmitter is held and the location.
2. In certain areas, the operational range will be reduced due to the vehicle body shape and the influence of the surrounding environment.
3. Since the transmitter uses weak radio waves, the operational range may be reduced or the transmitter may not function if interference or stronger radio waves occur in the area where the transmitter is used.
4. When the battery is low, the operational range is reduced and/or the transmitter may not function.

HINT: If the transmitter has been left in a place that is exposed to direct sunlight, such as on the instrument panel, the battery may be weakened or other problems may occur.

2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

HINT:
- The switches built into the door control transmitter send radio waves to the door control receiver.
- The operational range must be taken into account during checks.

a. Establish conditions that allow the wireless control function to be operated successfully.

b. Check the basic functions.
1. Check that all the doors lock when LOCK is pressed.
2. Check that all the doors unlock when UNLOCK is pressed.

c. Check the panic alarm function.
1. Check that if PANIC is held down for 0.8 seconds or more, the theft deterrent alarm function sounds the horn, and flashes the headlights, taillights and hazard warning lights for 27.5 seconds. And with the theft deterrent alarm function active, check if pressing any switch on the transmitter stops the horn and turns off the headlights, taillights and hazard warning lights.

d. Check the automatic locking function.
1. Check that the doors automatically relock if all the doors are unlocked by pressing UNLOCK and none of the doors is opened or locked within approximately 30 seconds.
2. Check that the automatic lock function does not operate if all of the doors are unlocked by pressing UNLOCK and a door is opened or locked within approximately 30 seconds.

e. Check the door ajar warning function.
1. Check that if a door is open or not completely closed, the doors cannot be locked by pressing LOCK and the wireless door lock buzzer sounds for about 10 seconds.

f. Check the interior light ON function.

HINT: Move the interior light switch to the DOOR position before the check.

1. Check that the interior light comes on simultaneously with the unlocking operation when the switch has been pressed for 1 second.
2. Check that the interior light goes off in approximately 15 seconds if none of the doors is opened after the unlocking operation.

g. Check the repeat function.
1. Check that all doors attempt to automatically lock once again 1 second after LOCK has been pressed while one of the door lock knobs is held in the unlocked position.

h. Check the answer back function.
1. When LOCK is pressed, check that the hazard warning lights flash once and the wireless door lock buzzer sounds once simultaneously with the locking of all the doors.
2. When UNLOCK is pressed, check that the hazard warning lights flash twice and the wireless door lock buzzer sounds twice simultaneously with the unlocking of all the doors.

i. Check the switch operation fail-safe function.
1. Check that the doors cannot be locked by the switch while the key is in the ignition key cylinder.

HINT: This check cannot be made when the system is in the recognition code registration mode.

j. Check the chattering prevention function.
1. Check that the selected operation occurs only once, and does not repeat itself while the switch is kept pressed. Check that the selected operation is carried out when the switch is operated repeatedly at 1 second intervals.