Front Manual Seat
REMOVAL1. REMOVE SEAT TRACK BRACKET COVER OUTER FRONT LH
a. Move the front seat assembly to the rear most position by operating the slide handle.
b. Using a screwdriver, disengage the 2 claws and remove the seat track bracket cover outer front LH.
HINT: Tape the screwdriver tip before use.
2. REMOVE SEAT TRACK BRACKET COVER INNER FRONT LH
a. Using a screwdriver, disengage the 2 claws and remove the seat track bracket cover inner front LH.
HINT: Tape the screwdriver tip before use.
3. REMOVE SEAT TRACK COVER LH
a. Move the front seat assembly fully forward by operating the slide handle.
b. Using a screwdriver, disengage the 2 claws and remove the seat track cover LH.
HINT: Tape the screwdriver tip before use.
4. REMOVE SEAT TRACK COVER RH
a. Using a screwdriver, disengage the 2 claws and remove the seat track cover RH.
HINT: Tape the screwdriver tip before use.
5. REMOVE FRONT SEAT ASSEMBLY (w/o Front Seat Side Airbag)
a. Move the front seat assembly to the rearmost position by operating the slide handle.
b. Remove the 2 bolts on the front side.
c. Move the front seat assembly fully forward by operating the slide handle.
d. Remove the 2 bolts on the rear side.
e. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.
f. Disconnect the connectors and clamp.
g. Remove the front seat assembly.
NOTE: When removing the passenger side front seat assembly, be careful not to step on the yaw rate sensor mounted on the floor under the seat.
6. REMOVE FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)
a. Move the front seat assembly to the rearmost position by operating the slide handle.
b. Remove the 2 bolts on the front side.
c. Move the front seat assembly fully forward by operating the slide handle.
d. Remove the 2 bolts on the rear side.
e. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.
f. Disconnect the negative terminal cable from the battery.
CAUTION: Wait 90 seconds or more after disconnecting the negative terminal cable to prevent the airbag from deploying.
g. Disconnect the connectors and clamp.
h. Remove the front seat assembly.
NOTE: When removing the passenger side front seat assembly, be careful not to step on the yaw rate sensor mounted on the floor under the seat.
INSTALLATION
1. INSTALL FRONT SEAT ASSEMBLY (w/o Front Seat Side Airbag)
a. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.
NOTE: When installing the passenger side front seat assembly, be careful not to step on the yaw rate sensor mounted on the floor under the seat.
b. Connect the connector.
c. Move the front seat assembly to the rearmost position by operating the slide handle.
NOTE: Check that the seat is locked.
d. Temporarily install the front side of the front seat assembly with the 2 bolts.
e. Move the front seat assembly fully forward by operating the slide handle.
NOTE: Check that the seat is locked.
f. Temporarily install the rear side of the front seat assembly with the 2 bolts.
g. Move the front seat assembly to the rearmost position by operating the slide handle.
NOTE: Check that the seat is locked.
h. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
i. Move the front seat assembly fully forward by operating the slide handle.
NOTE: Check that the seat is locked.
j. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
2. INSTALL FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)
a. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.
NOTE: When installing the passenger side front seat assembly, be careful not to step on the yaw rate sensor mounted on the floor under the seat.
b. Connect the connector.
c. Install the clamp.
d. Move the front seat assembly to the rearmost position by operating the slide handle.
NOTE: Check that the seat is locked.
e. Temporarily install the front side of the front seat assembly with the 2 bolts.
f. Move the front seat assembly fully forward by operating the slide handle.
NOTE: Check that the seat is locked.
g. Temporarily install the rear side of the front seat assembly with the 2 bolts.
h. Move the front seat assembly to the rearmost position by operating the slide handle.
NOTE: Check that the seat is locked.
i. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
j. Move the front seat assembly fully forward by operating the slide handle.
NOTE: Check that the seat is locked.
k. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
3. INSTALL SEAT TRACK COVER RH
4. INSTALL SEAT TRACK COVER LH
5. INSTALL SEAT TRACK BRACKET COVER INNER FRONT LH
6. INSTALL SEAT TRACK BRACKET COVER OUTER FRONT LH
7. PERFORM INITIALIZATION
Some systems need initialization when disconnecting the cable from the negative battery terminal.
8. INSPECT SLIDE ADJUSTER LOCK
a. Check that the left and right adjusters lock simultaneously when sliding the seat.
b. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.
9. INSPECT SEAT HEATER OPERATION (w/ Seat Heater System)
10. INSPECT SRS WARNING LIGHT